Star Headlight & Lantern M-Tech DL35-12 Manual Download | Manualshive

Page: 3 / 20

background image

ii

Table of Contents

WARNINGS

i

ASSEMBLY

1-3

MOUNTING

4-5

DL35-6 and DL35-12 Mounting

4

DL35-6-1 and DL35-12-1 Mounting

5

OPERATION

6-15

DL35-6 and DL35-12

6-8

DL35-6-1 and DL35-12-1

9-15

WARRANTY

16

SERVICE

16

NOTICE

Due to continuous product improvements, we must reserve the right to change any
specifications and information, contained in this manual at any time without notice. Star
Headlight & Lantern Co., Inc. makes no warranty of any kind with regard to this manual,
including, but not limited to, the implied warranties of merchantability and fitness for a
particular purpose. Star Headlight & Lantern Co., Inc. shall not be liable for errors contained
herein or for incidental or consequential damages in connection with the furnishing,
performance, or use of this manual.

Please Note:

These instructions are provided as a general guideline only. Specific

mounting, wiring, and/or weather-sealing may be necessary and are the sole
responsibility of the installer. Star Headlight & Lantern Co., Inc. assumes no
responsibility for the integrity of the installation for this or any of its products.

«
1
2
3
4
5
...
»

Summary of Contents for M-Tech DL35-12





















Reviews:

No comments

Related manuals for M-Tech DL35-12

Brand: Canon Pages: 10

AVCCAM AG-HMR10

Brand: Panasonic Pages: 4

Brand: Samsung Pages: 2

Brand: Ecco Pages: 4

ESCALADE - BROCHURE 2009

Brand: Cadillac Pages: 24

Brand: Cadillac Pages: 20

Brand: Cadillac Pages: 20

Brand: Safemate Pages: 12

Brand: Obelink Pages: 2

Brand: Leuze Pages: 9

Brand: rako Pages: 7

Brand: Saft Pages: 6

Brand: M-Audio Pages: 14

Brand: Öhlins Pages: 8

Brand: Öhlins Pages: 9

Brand: Omron Pages: 16

Brand: GOgroove Pages: 9

WaterGuard CM2300

Brand: Mobeye Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands