-28-
(Service CONT’D)
PARTS
SPECIFICATIONS
Input Voltage
10 - 16 VDC (negative ground)
Siren Input Current
8.0 Amps @ 13.6 VDC (single 100W speaker)
16 Amps @ 13.6 VDC (dual 100W speakers)
Siren Standby Current
Less than 10 mA when ignition is off
Audio Frequency
200Hz - 10 kHz + 3db
Siren Output Power
105 WATTS RMS MAX. (15.0 VDC - single 100W speaker)
210 WATTS RMS MAX. (15.0 VDC - dual 100W speakers)
Siren Frequency
675Hz - 1633Hz
High Voltage Protection
16 - 18 VDC will cause siren output to temporarily cease, resume at normal
Short Circuit Current
50 AMPS (supply circuit must be capable of supplying this)
Operating Temperature
-15° F to +140°F
Siren Controls
5-illuminated push button switches (Hands Free, Wail, Yelp, Phaser, and Radio)
Momentary push button Horn and Manual/Toggle switch
Auxiliary input connection for remote Manual/Horn operation (jumper programmable
for positive or negative horn)
Park Kill input connection (jumper programmable for positive or negative activation)
Phaser (and Two-Tone) disable (jumper programmable)
Two-Tone activation swaps modes with Phaser (jumper programmable)
Diagnostic Indicators
Two LED indicators provide diagnostic feedback, one for each speaker
Light Controls
4 push-on/push-off buttons (1 programmable 8 sec. time delay)
4-position slide switch (Off, L1, L1 & L2, L1 & L2 & L3 & Wail)
Light Output Ratings
20A fuse on each of the 7 light outputs. (4 push buttons, 3 slide positions)
Siren Connections
(12-Pin Connector)
(Telephone Comm. Con.)
Detachable, 12-pin, positive locking connector with pigtail leads for Amplifier
(2) Positive, (2) Negative, (2) Speaker, (2) Radio, Auxiliary, Park Kill
Telephone style communication cable between Control Head and Amplifier
Light Control Connections
+12 - three position barrier style terminal block
L1, L2, L3 (Slide Switch) 3-position Eurostyle terminal block
S1, S2, S3, S4 (Push buttons) 4-position Eurostyle terminal block
S5 (Push button) flying lead
Arrow Stick Connections
12 position, positive locking connector
Size
Amplifier: 2-1/2” High, 7” Wide, 7-3/8” Deep (plus 3/4" flange on each side)
Hand Held Controller: 6" High X 2-1/2" Wide X 1-1/4" Deep
Arrow Stick Control Box: 1-9/16” H X 6” W X 4-1/2” D (TDC850)
Boxed Weight
LCS880: 8.5 lbs. LCS881: 9.25 lbs.
Part
Description
LCS850-AMP8
Amplifier Only
LCS880-CH
Hand-Held Controller for LCS880
LCS881-C
Hand-Held Controller for LCS881
TDC850
Arrowstick Power Supply
P30255-43A
Amp Wiring Harness
30008-22
25’ Communication Cable Between Control Head Cable and Amp*
30041-52
Female/Female RJ11 Connector for Communication Cables
30008-30
7’ Communications Cable Between TDC850 and Amp (LCS881 only)*
P30041-188
Control Head/TDC850 Splitter for Communications Cable (LCS881 only)
SWH-140
12” Communication Cable (LCS881 only)
30028-8
5 Amp Automotive Blade Fuse inside Amplifier (also used in TDC850)
30028-1
20 Amp Automotive Blade Fuse for Amplifier (also used in TDC850)
30007-66-1
Knob for Slide Switch
S30007-66-2
Slide Switch Assembly (less control knob)
P30232-4
LCS880-CH/LCS881-CH Microphone
P30053-31
Amplifier Case Screws
P30032-8
TIP36C Power Transistor
* CAUTION:
These are not a standard telephone cables and CANNOT be replaced with one.
