Stanley MA900n, Installation And Owner'S Manual

Page: 33 / 36

TDM
Universal Time Delay Module INSTALLATION INSTRUCTIONS
8701 Castle Park Drive „ Indianapolis, Indiana 46256
Telephone: (800) 842-2545/(317) 842-2545
„
www.mssedco.com
„
custsvc@mssedco.com
Page 3
(82A044) TDMv0605
FIGURE 2—Simple Time Delayed Output
Once the TDM has been wired for the above application, programming of the device is as follows:
1) Apply power to the unit, provided there is no smoke or fire, you can assume that your wiring job must
be somewhat successful.
2) Once properly powered, the display will flash double bars ( –– ) indicating that the unit is in its normal
operating ready mode.
3) To begin programming, depress the PROGRAM MODE BUTTON one time. The first parameter to be
programmed will appear on the display. This is the delay time, or "on time" of the output #1 and is
displayed as d1 followed by the time setting (It will flash between the two). To adjust the time setting,
use a small screwdriver and rotate the DISPLAY ADJUSTMENT clockwise to increase and
counterclockwise to decrease the time setting. After the desired value is displayed, depress the
PROGRAM MODE BUTTON again to save the value. The display will now read d2 . Now wait 30
seconds until the display again reads double bars ( –– ) indicating that the unit is in its normal
operating ready mode.
4) You are now ready to test your installation. If the time delay has to be changed, make the change to
the
d1 setting, press the PROGRAM MODE BUTTON once and then wait 30 seconds until the double
bars ( –– ) appear again.
5) During operation of the unit, the display will indicate its operating status. Please refer to Figure 5 at
the end of this installation manual.
or Electric Exit Device or Electric Exit Device
Wall Wall
Switch Switch
PUSH PUSH
TO TO
OPEN OPEN
WHT/BLU WHT/BLU
BLU BLU
MS SEDCO MS SEDCO
TDM TDM
Timing Control Module Timing Control Module
N.C. N.C.
Output #1 Output #1
Input #1 Input #1
SPRINKLER SPRINKLER
OR FIRE OR FIRE
DETECTION DETECTION
SYSTEM SYSTEM
(IF USED)
(IF USED)
FIRE FIRE
SYSTEM SYSTEM
(IF USED) (IF USED)
PROTECTION PROTECTION
SIGNALING SIGNALING
Mag Lock Mag Lock
N.C. N.C.
N.C. N.C.
AC / DC AC / DC
G
R
N
GRN
G
R
N
GRN
GRAY GRAY
VIO VIO
JUMPER
INSTALLED
FOR "DRY"
CONTACTS
JUMPER
INSTALLED
FOR "DRY"
CONTACTS
12-24V 12-24V
12-24V 12-24V
This separate power source ( & associated wiring) can be eliminated
if the jumper is set for "WET" contacts instead of "DRY" contacts.
(see page 5)
This separate power source ( & associated wiring) can be eliminated
if the jumper is set for "WET" contacts instead of "DRY" contacts.
(see page 5)
TDM TDM
IN
PU
T
4
INPUT 4
IN
PU
T
3
INPUT 3 IN
PU
T
2
INPUT 2
IN
PU
T
1
INPUT 1
12
-2
4V
A
C
/D
C
12-24V AC/DC
IN
PU
T
1
INPUT 1
C
O
M
COM
C
O
M
COM
C
O
M
COM
C
O
M
COM
N
.O
.
N.
O
.
N
.C
.
N.
C.
N
.C
.
N.
C.
N
.O
.
N.
O.
PROGRAM PROGRAM
MODE BUTTON MODE BUTTON
DISPLAY DISPLAY
ADJUSTMENT
ADJUSTMENT
LED DISPLAY KEY LED DISPLAY KEY
d1 = delay 1 d1 = delay 1
d2 = delay 2
d2 = delay 2
d3 = delay d1 to d2
d3 = delay d1 to d2
d4 = delay d2 to d1
d4 = delay d2 to d1
i1 = input 1 (n.o. / n.c.)
i1 = input 1 (n.o. / n.c.)
i3 = input 3 (n.o. / n.c.) i3 = input 3 (n.o. / n.c.)
i2 = input 2 (n.o. / n.c.) i2 = input 2 (n.o. / n.c.)
i4 = input 4 (n.o. / n.c.) i4 = input 4 (n.o. / n.c.)
o2 = output 2 (n.o. / n.c.) o2 = output 2 (n.o. / n.c.)
o1 = output 1 (n.o. / n.c.) o1 = output 1 (n.o. / n.c.)
o1
=
d
ry
o1= dry
o1
=
w
et
o1= wet
Output #1 Output #1
Output #2 Output #2
PROGRAMMING
PROCEDURE
NOTE:
Mag Lock uses N.C.
(Gray
& Violet)
Electric Exit device uses
N.O. (Gray & White)