background image

BEST ACCESS SYSTEMS

a Product Group of Stanley Security Solutions, Inc

1

Power
supply

Lock

Wire
transfer
hinge

Field wire 

harness

Power (2)

RS-485 Communication (2)

Communication tamper (2)

  
Door status (2)

RQE status (2)

Strike (2)

Token data (2)

Reader LED (2)

Sounder (2)

Card present (1)

Panel interface
module

Access
control
panel/
reader
interface

Power (2)

Power
supply

Overview

The 83KM/93KM–85KM/95KM IDH Max Cylindrical Lock 
provides the following features in an integrated lock, 
eliminating the need to install separate sensors in and 
around the door frame:

electrified locking mechanism

electronic token reader

integrated trim

door status detection

ability to exit without triggering an alarm

compatibility with varied access control panels/
reader interfaces.

Note: For a list of compatible access control panels/
reader interfaces, contact your local Stanley® 
representative.

A panel interface module is provided with the lock. The 
panel interface module receives token data and lock 
sensor data from the lock through an RS-485 connection. 
It translates this data into parallel signals, which it sends 
to the access control panel/reader interface. The panel 
interface module also translates control signals received 
from the access control panel/reader interface and sends 
them to the lock.
The figure below shows the relationship between the 
components in the IDH Max system.

Contents

These installation instructions describe how to install, 
wire, and configure the components provided with your 
83KM/93KM–85KM/95KM IDH Max Cylindrical Lock. The 
following topics are covered.

Site survey

....................................................................... 2

Components checklist

................................................... 2

Special tools checklist

.................................................... 3

Preparing the door and door jamb

.............................. 4

Installing the lock 

........................................................ 10

Completing the installation at the door

................... 17

Installing the panel interface module

....................... 18

Testing the installation

................................................ 23

Troubleshooting the installation

............................... 24

Installation Instructions for 83KM/93KM–
85KM/95KM IDH Max Cylindrical Locks

Summary of Contents for 83KM-93KM

























Reviews: