ST HTSSOP38 Manual Download Page 65 | Manualshive

Page: 65 / 73

background image

L6482

Programming manual

Doc ID 023768 Rev 1

65/73

This command can be given only when the previous motion command has been completed
(BUSY flag released).

Any attempt to perform a GoTo command when a previous command is under execution
(BUSY low) causes the command to be ignored and the NOTPERF_CMD flag to rise
(

Section 9.1.21

9.2.9

GoTo_DIR (DIR, ABS_POS)

The GoTo_DIR command produces a motion to the ABS_POS absolute position imposing a
forward (DIR = '1') or a reverse (DIR = '0') rotation. The ABS_POS value is always in
agreement with the selected step mode; the parameter value unit is equal to the selected
step mode (full, half, quarter, etc.).

The GoTo_DIR command keeps the BUSY flag low until the target speed is reached. This
command can be given only when the previous motion command has been completed
(BUSY flag released).

Any attempt to perform a GoTo_DIR command when a previous command is under
execution (BUSY low) causes the command to be ignored and the NOTPERF_CMD flag to
rise (

Section 9.1.21

).

9.2.10

GoUntil (ACT, DIR, SPD)

The GoUntil command produces a motion at SPD speed imposing a forward (DIR = '1') or a
reverse (DIR = '0') direction. When an external switch turn-on event occurs (

the ABS_POS register is reset (if ACT = '0') or the ABS_POS register value is copied into
the MARK register (if ACT = '1'); the system then performs a SoftStop command.

The SPD value is expressed in step/tick (format unsigned fixed point 0.28) that is the same
format as the SPEED register (

Section 9.1.4

The SPD value should be lower than MAX_SPEED and greater than MIN_SPEED,
otherwise the target speed is imposed at MAX_SPEED or MIN_SPEED respectively.

Table 55.

GoTo_DIR command structure

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

0

1

1

0

1

0

0

DIR

from host

X

X

ABS_POS (Byte 2)

from host

ABS_POS (Byte 1)

from host

ABS_POS (Byte 0)

from host

Table 56.

GoUntil command structure

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

1

0

0

0

ACT

0

1

DIR

from host

X

X

X

X

SPD (Byte 2)

from host

SPD (Byte 1)

from host

SPD (Byte 0)

from host

«
...
63
64
65
66
67
...
»

Summary of Contents for HTSSOP38










































































Reviews:

No comments

Related manuals for HTSSOP38

Brand: Rane Pages: 4

Brand: Baldor Pages: 34

Brand: Gate Pages: 8

iTRON B 70.2040

Brand: JUMO Pages: 41

Brand: Renesas Pages: 4

Brand: H3C Pages: 9

Brand: Magewell Pages: 10

Brand: Z3 Technology Pages: 18

Brand: Keithley Pages: 108

Brand: Advantech Pages: 70

CU8210-D001-0200

Brand: Beckhoff Pages: 25

Brand: Renfert Pages: 29

Brand: Swann Pages: 30

Brand: Optimus Pages: 16

Brand: X-Micro Pages: 9

Brand: X-Micro Pages: 17

Brand: X-Micro Pages: 31

My Cloud EX2 Ultra

Brand: Western Digital Pages: 169

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands