ST HTSSOP38 Manual Download Page 45

Page: 45 / 73

L6482

Programming manual

Doc ID 023768 Rev 1

45/73

with the step mode selected in the STEP_MODE register in order to avoid a wrong
microstep value generation (

Section 9.1.17

); otherwise the resulting microstep sequence is

incorrect.

Any attempt to write the register when the motor is running causes the command to be
ignored and the NOTPERF_CMD flag to rise (

Section 9.1.21

9.1.3 MARK

The MARK register contains an absolute position called MARK, according to the selected
step mode; the stored value unit is equal to the selected step mode (full, half, quarter, etc.).
It is in 2's complement format and it ranges from -2

to +2

-1.

9.1.4 SPEED

The SPEED register contains the current motor speed, expressed in step/tick (format
unsigned fixed point 0.28).

In order to convert the SPEED value in step/s, the following formula can be used:

Equation 1

where SPEED is the integer number stored in the register and tick is 250 ns.

The available range is from 0 to 15625 step/s with a resolution of 0.015 step/s.

Note:

The range effectively available to the user is limited by the MAX_SPEED parameter.

Any attempt to write the register causes the command to be ignored and the
NOTPERF_CMD flag to rise (

Section 9.1.21

9.1.5 ACC

The ACC register contains the speed profile acceleration expressed in step/tick

(format

unsigned fixed point 0.40).

In order to convert the ACC value in step/s

, the following formula can be used:

Equation 2

where ACC is the integer number stored in the register and tick is 250 ns.

The available range is from 14.55 to 59590 step/s

with a resolution of 14.55 step/s

When the ACC value is set to 0xFFF, the device works in infinite acceleration mode.

Any attempt to write to the register when the motor is running causes the command to be
ignored and the NOTPERF_CMD flag to rise (

Section 9.1.21

step/s

[

]

SPEED

–

⋅

tick

----------------------------------------

step/s

[

]

ACC

–

⋅

tick

-------------------------------

Summary of Contents for HTSSOP38










































































Search results

Summary of Contents for HTSSOP38

Reviews:

Related manuals for HTSSOP38

Brands by name

Popular brands

ST HTSSOP38, Manual

Search results

Summary of Contents for HTSSOP38

Reviews:

Related manuals for HTSSOP38

Brands by name

Popular brands