manualshive.com logo in svg

SSB-Electronic Zeus-1, Operation Manual

Share
Download
SSB-Electronic Zeus-1 Operation Manual Download Page 45

Software description

Predistortion Setup

4 Comments Field

Comment input field to a given set of settings.

5 Buttons for selection of band-dependant predistortion algorithms

6 Mode A, B, C Buttons

Button selects one of three predistortion algorithms.

7 Max Power Parameter

Max Power parameter sets the maximum output power of the transceiver with an

external amplifier in the selected frequency range, ie limits the maximum value for
the ZS-1 Signal and Carrier power adjustment in the main program window.

8 Alfa, Beta, Gamma Parameters

The coefficients of the predistortion algorithm for the selected frequency band.
For coarse adjustment parameter can  be set by  arrows up / down in the input

field or rotate the mouse wheel. Keyboard input of a certain value is also possible.

9 Enable Button

Enable / disable the predistortion algorithm in the selected frequency range.

10 Spacing List

Drop-down list, selects the separation of the two tones.

11 Power Field

Field for the power of two-tone signal (PEP).

12 2-tone TX Button

On/off switch for two-tone signal transmission with given power and spacing

between tones.

The controls located in the section intended for Low Power setting algorithms at a

low output power (LPW), to be activated by pressing "LPW" in the main window.

SSB-Electronic GmbH ©     Page 45 of 88      V2.8.1     C

ontent is protected by Copyright.                 

Summary of Contents for Zeus-1

























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands