manualshive.com logo in svg

SSB-Electronic Zeus-1, Operation Manual

Share
Download
SSB-Electronic Zeus-1 Operation Manual Download Page 27

Software description

Main window

46 Spectrum/waterfall ratio control field

By moving the line below the frequency axis upwards or downwards with the left

mouse   button   pressed   the   vertical   size   of   the   spectrum   and   waterfall   can   be
changed.

47 Audio signal recording button

By left-button mouse click an audio file recording is started. A recording includes

received and transmitted signals. During a recording the button blinks. A further
click will stop the recording.

By right-button mouse click a dialogue window will appear for defining the folder

where an audio files will be stored. When selecting the folder it has to be ensured
that the user has rights to write into this folder. Else no recordings can be stored.

It is possible to choose the file type of audio recordings: wav or ogg. OGG files are

compressed and therefore smaller. WAV files are bigger, but are suited better for
later analysis or processing.

48 IQ data recording button

By left-button mouse click an IQ data file recording is started. During a recording

the button blinks. A further click will stop the recording. While recording IQ data,
transmitting is not possible.

Recording of IQ data file is possible for spectrum bandwidths up to 100 kHz.
Recording can be replayed with the IQ Player software.
By right-button mouse click a dialogue window will appear for defining the folder

where an IQ data files will be stored. When selecting the folder it has to be ensured
that the user has rights to write into this folder. Else no recordings can be stored.

Note: Recorded files can be huge. A one minute long recording of 100 kHz bandwidth will have a
file size of 43 MB. A maximum file size of 200 MB is defined by software; as soon this value is
reached, a new file is created automatically. Recording that consists of several files are treated as
a single file by the IQ Player software and will be replayed without interruption.

49 Button for audio file transmission

Clicking this button will replay an audio file; simultaneously this file is transmitted.

This allows a comfortable modulation control for the partner station or repeat your
call sign some times.

SSB-Electronic GmbH ©     Page 27 of 88      V2.8.1     C

ontent is protected by Copyright.                 

Summary of Contents for Zeus-1

























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands