manualshive.com logo in svg

Spectrum fieldscout TDR 300, Product Manual, Page: 6 / 32

Share
Download
Spectrum fieldscout TDR 300 Product Manual Download Page 6

6 

NOTE: The dataloggers do not short-circuit the serial pin.  
Therefore, when the 

Test Port

 button is clicked while the 

meter is connected, the “No Connection” message will be 
displayed. 

T h e   c o m p u t e r 

Com

munications 

Port

 to 

which the PC-3.5 serial 
cable is connected can be 
identified by using a 
paper clip. 

1. Disconnect the serial 
cable  from the meter. 

2. To bring up the 

Port Selection 

screen, click on the 

Com Port 

Button, select the com port to be tested and 

click the 

Port Test

 button.  Click the 

Test Port Now 

button. If the message “Connection OK” is displayed, 
another device (such as a modem) is probably connected 
to that port. If the message “No Connection” is displayed, 
this port may be the one connected to your serial cable and 
you can proceed to the next step. 

3. Place a paperclip on the end of the serial pin so that it 
touches both the tip of the pin and the metal area between 
the two black rings.   Again click on the 

Test Port Now 

button.  If the message “Connection OK” now appears, 
this is the com port connected to your serial cable.   

paper clip 
or wire 

Identifying the  

Correct Com Port 

 

Summary of Contents for fieldscout TDR 300

































Reviews:

No comments