Spectrum fieldscout TDR 300 Product Manual Download Page 5 | Manualshive

Page: 5 / 32

Spectrum fieldscout TDR 300 Product Manual Download Page 5

5

TDR 300

data port

Software Installation

Insert the CD for Field Scout software into your PC’s disk
drive. If auto-start is not enabled on your computer, select

Run

from the

Start

menu and type

D:\Setup.exe

(Substitute the appropriate drive letter for your CD drive).
Click

OK

and follow the instructions on the screen.

The data port on the underside of the TDR 300 meter
(shown above) can be accessed by removing the plastic
screw. It is through this port that the meter is connected
to either a PC or to a GPS unit. The meter must be turned
off before attempting communication with the software.

Connecting to a PC

The Field Scout software comes with a gray PC interface
cable. This cable connects to the 9-pin serial port of your
computer and to the meter’s computer port. The meter’s
configuration can be modified by clicking on the

Meter

Settings

button (see Meter Settings, p. 16). The

Com

Port, Meter Type, Download,

Clear Memory

and

Me-

ter Settings

buttons are explained in the Field Scout Soft-

ware Toolbar section (p. 14).

Changing the batteries

The battery compartment is accessed by removing the me-
ter’s face plate. The meter is powered by AAA batteries.

When installing new batteries, note whether the bat-
teries immediately feel hot to the touch. The battery
has been short-circuited and should be replaced.

Computer Interface/

Changing Batteries

«
...
3
4
5
6
7
...
»

Summary of Contents for fieldscout TDR 300

































Reviews:

No comments