manualshive.com logo in svg

Spectrum fieldscout TDR 300, Product Manual, Page: 11 / 32

Share
Download
Spectrum fieldscout TDR 300 Product Manual Download Page 11

  11 

Taking Readings 

- Remove one of the 
hand screws from the 
shaft.  This will allow 
you to unfold the shaft 
to its full length.  Re-
turn the screw to lock 
the shaft in the ex-
tended position. 

 
 
 
- Screw the rods into 
the sockets at the bot-
tom of the probe block.   
 
 
 
 

- Turn on the meter and ensure that it is configured with 
the correct rod length setting (see Changing Rod Length, 
p. 8).   
 
- Select the correct mode setting (see Data Collection 
Modes, p. 8).  This will bring you to one of the data col-
lection screens.  The TDR 300 can be set to one of two 
VWC  modes,  Standard  or  High Clay.The Standard 
mode will be appropriate for most mineral soils. The 
High Clay mode will be more accurate for soils with 
higher clay contents (>27%).  In VWC mode, the top 
line of the display shows the VWC mode and the water 
content.  The bottom line has probe setting and data file 
information. 
 

 

Summary of Contents for fieldscout TDR 300

































Reviews:

No comments