Spectrum DX8G2 Instruction Manual Download Page 32

Page: 32 / 53

SPEKTRUM DX8G2 • TRANSMITTER INSTRUCTION MANUAL

FUNCTION LIST

The Speed menu enables you to slow the response time on any

individual channel (such as retracts).

The Speed is adjustable in the following ranges:

•  Nor (No Delay) – 0.9s in 0.1 second increments
•  1s – 2s in 0.2-second increments
•  2s – 8s in 1-second increments

To adjust the Speed:

1. Scroll to the channel

you wish to adjust

and press the scroll

wheel.

2. Scroll left or right

to adjust the speed

and press the scroll

wheel to save the

selection.

Balance is available on all channels to fine-tune the servo position

at up to 7 points. This is a precision curve mix that is normally

used to prevent binding when multiple servos are used on a single

control surface.

You can also use the Balance menu option to match throttle

response on twin engine aircraft or level the swashplate on a

helicopter.

When using a compatible AS3X receiver (AR636, AR6335,

AR9350, etc.), Gain Live View allows

•  Real time display of gain values for Roll Pitch and Yaw
•  Allows gains to be adjusted from the roller
•  Selection of the channel that is used to adjust gains (must match

application)

• Selection of the switch that is used to change flight modes

To activate AS3X gain Live View:

1. In the telemetry screen in one of the empty positions select

AS3X and activate the Display. This will activate the AS3X Gain

menu in the Function List.

2. In the Function List Access the AS3X Gain menu. If an AS3X

receiver is bound to the transmitter and the receiver and

transmitter are on, live gain values will be displayed on this

screen.

Axis:

Roll Pitch and Yaw gain are displayed to the right of each Axis

Rate:

Rate gain values are displayed here

Heading:

Heading gain values are displayed here

Actual:

The current gain value is displayed here. Note that this value

takes into account the priority gain and the stick position of

that channel

Gain:

This value represents the position of the input (roller or knob)

Input:

Allows the selection of the roller to be used to adjust the gain

Channel:

Must correspond to the channel selected in the AS3X

application in the FM Channel Assignment screen

FM Switch:

Selects the switch on the transmitter that is used to

select the flight modes in the AS3X system

Note that relative (REL) must be selected in the application’s gain

screen to allow adjustable gain from the transmitter.

Please see the following web address for videos and information

about setting up the AS3X application, Live View and adjusting the

gain from the transmitter.
http://www.spektrumrc.com/Technology/AS3X.aspx



Speed



Balance



AS3x Gain Live View (ACRO and SAIL Types only)

Summary of Contents for DX8G2






















































Search results

Summary of Contents for DX8G2

Reviews:

Related manuals for DX8G2

Brands by name

Popular brands

Spectrum DX8G2, Instruction Manual

Search results

Summary of Contents for DX8G2

Reviews:

Related manuals for DX8G2

Brands by name

Popular brands