Spectrum DX8G2 Instruction Manual Download Page 51

Page: 51 / 53

SPEKTRUM DX8G2 • TRANSMITTER INSTRUCTION MANUAL

This device complies with part 15 of the FCC rules. Operation is

subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including

interference that may cause undesired operation.

CAUTION:

Changes or modifications not expressly

approved by the party responsible for compliance could

void the user’s authority to operate the equipment.

This product contains a radio transmitter with wireless technology

which has been tested and found to be compliant with the

applicable regulations governing a radio transmitter in the

2.400GHz to 2.4835GHz frequency range.

Antenna Separation Distance

When operating your Spektrum transmitter, please be sure to

maintain a separation distance of at least 5 cm between your body

(excluding fingers, hands, wrists, ankles and feet) and the antenna

to meet RF exposure safety requirements

as determined by FCC regulations.

The following illustration shows the

approximate 5 cm RF exposure area and

typical hand placement when operating

your Spektrum transmitter.

Prior to flying, contact your local or regional modeling organizations

for guidance and familiarize yourself with the current local rules

and FAA regulations governing model aviation in your location.

More information about model aviation can be found at

www.modelaircraft.org.
The Federal Aviation Administration can be found online at

www.faa.gov.

IC INFORMATION

This device complies with Industry Canada licence-exempt RSS

standard(s). Operation is subject to the following two conditions:

(1) this device may not cause interference, and (2) this device must

accept any interference, including interference that may cause

undesired operation of the device.

AMA NATIONAL MODEL AIRCRAFT SAFETY CODE

http://www.modelaircraft.org/files/105.PDF

WARRANTY AND SERVICE CONTACT INFORMATION

FCC INFORMATION

FAA INFORMATION

Country of Purchase

Horizon Hobby

Contact Information

Address

United States of

America

Horizon Service Center

(Repairs and Repair Requests)

servicecenter.horizonhobby.com/

RequestForm/

4105 Fieldstone Rd

Champaign, Illinois, 61822 USA

Horizon Product Support

(Product Technical Assistance)

[email protected]

877-504-0233

Sales

[email protected]

800-338-4639

United Kingdom

Service/Parts/Sales:

Horizon Hobby Limited

[email protected]

Units 1–4 , Ployters Rd, Staple Tye

Harlow, Essex, CM18 7NS, United Kingdom

+44 (0) 1279 641 097

Germany

Horizon Technischer Service

[email protected]

Christian-Junge-Straße 1

25337 Elmshorn, Germany

Sales: Horizon Hobby GmbH

+49 (0) 4121 2655 100

France

Service/Parts/Sales:

Horizon Hobby SAS

[email protected]

11 Rue Georges Charpak

77127 Lieusaint, France

+33 (0) 1 60 18 34 90

Summary of Contents for DX8G2






















































Search results

Summary of Contents for DX8G2

Reviews:

Related manuals for DX8G2

Brands by name

Popular brands

Spectrum DX8G2, Instruction Manual

Search results

Summary of Contents for DX8G2

Reviews:

Related manuals for DX8G2

Brands by name

Popular brands