Spectrasensors SS1000 Operator'S Manual Download Page 13

Page: 13 / 83

SS1000 Operator’s Manual

–

1 - I

NTRODUCTION

SpectraSensors SS1000 products are high-speed, diode-laser based extractive

analyzers designed for extremely reliable monitoring of very low (trace) to

standard concentrations of H

O or CO

in Natural Gas. In order to ensure that

the analyzer performs as specified, it is important to pay close attention to the

details of the installation and operation. This manual contains a comprehensive

overview of the SS1000 analyzer and step-by-step instructions on:

•

Inspecting the Analyzer

•

Setting up the Analyzer

•

Powering Up the Analyzer

•

Operating the Analyzer

•

Serial Port Communications

•

Powering Down the Analyzer

•

Troubleshooting

Who Should Read This Manual

This manual should be read and referenced by anyone installing, operating, or

having contact with the analyzer.

How to Use This Manual

Take a moment to familiarize yourself with this Operator’s Manual by reading

the Table of Contents.
There are a number of options and accessories available for the SS1000

analyzers. This manual has been written to address the most common options

and accessories. Read each section in the manual carefully so you can quickly

and easily install and operate the analyzer.
The manual includes images, tables, and charts that provide a visual

understanding of the analyzer and its functions. Special symbols are also used

to make you aware of potential hazards, important information, and valuable

tips. Pay close attention to this information.

UK Distibution by IMA Ltd

Tel: +44 (0)1943 878877 Email: [email protected] Web: www.ima.co.uk

Summary of Contents for SS1000




















































































Search results

Summary of Contents for SS1000

Reviews:

Spectrasensors SS1000, Operator'S Manual, Page: 13 / 83

Search results

Summary of Contents for SS1000

Reviews: