Spearhead Twiga Carrier CF20 Operator'S Instruction Manual Download Page 25 | Manualshive

Page: 25 / 53

background image

8999145EN: v1 26/02/2020

25

Original instructions (ENGLISH)

Website: www.spearheadmachinery.com

  Start the tractor and engage the Hydraulic drive service.
  Switch on the rotor control from the prime mover cab.
  Check the direction of rotation of the rotor.
  Stop the rotor and the tractor.
  If the rotor has run in the wrong direction, reverse the large hoses on the motor.

Figure 4.1.1.5

– Line Up Holes On Cutting Unit

Insert the set screws and tighten to 80Nm torque.

Connect the ¾” motor hoses from the Twiga Carrier Arm to the cutting unit, using the male-male
adaptors included

Re-check all hydraulic connections and ensure all fasteners are secure and tight.
The Twiga Carrier Arm can now be lifted via the prime mover hydraulics, ready for cutting.

«
...
23
24
25
26
27
...
»

Summary of Contents for Twiga Carrier CF20






















































Reviews:

No comments

Related manuals for Twiga Carrier CF20

Brand: Cadet Pages: 13

Brand: Yard-Man Pages: 16

Brand: Tanaka Pages: 8

Brand: MacAllister Pages: 18

Brand: McConnel Pages: 108

ELM 34/1400 PLUS

Brand: F.F. Group Pages: 48

Brand: Honda Pages: 24

Brand: Parkside Pages: 124

Brand: MASSEY FERGUSON Pages: 31

Brand: Cub Cadet Pages: 24

Brand: Toro Pages: 44

Brand: Cub Cadet Pages: 44

Brand: Husqvarna Pages: 60

Brand: Husqvarna Pages: 60

Brand: Husqvarna Pages: 68

Brand: Husqvarna Pages: 36

Brand: Husqvarna Pages: 80

Brand: Husqvarna Pages: 48

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands