Speakman SV-4012 Installation Instructions Manual Download

Page: 5 / 6

COMPLIANCE

CONNECTIONS

ASSE 1037/ASME A112.1037
ASME A112.18.1/CSA B125.2
WaterSense

(For 1.28 GPF and 0.50 GPF models)

Inlet: 1” NPT Female

Outlet: 1-1/2” NPSM

ROUGH-IN DIAGRAM

DIMENSIONS SUBJECT TO CHANGE WITHOUT NOTICE. FOR ADA MOUNTING

LOCATIONS, CONSULT ADAAG, ANSI A117.1, AND LOCAL/STATE REGULATIONS.

NOTES

Installer to supply necessary inlet connections.

If you are cutting the vacuum breaker tube to size,

consult local plumbing codes to ensure that the critical

line is properly located above the fixture. Typically, the

critical line is 6” above the fixture.

FLOW RATE

SV-4012 1.28 GPF

SV-4016 1.60 GPF

15°

25 1/2" [650mm]

FACTORY SET RANGE

SENSOR EYE

1 12 "

38mm

228mm

1/2" [13mm] MIN

1 1/2" [38mm] MAX

4 5/16" [111mm] MIN

5 5/16" [137mm] MAX

8 1/8" [206mm] MIN

9 1/8" [232mm] MAX

1 18 "

28mm

1 38 "

35mm

2 9

16 "

65mm

1" [25mm] MIN

6" [152mm] MAX

4 9/16" [116mm] MIN

9 9/16" [243mm] MAX

2 5/8" [67mm] MIN

7 5/8" [194mm] MAX

17 5

16 "

440mm

11 12 "

293mm

1-1/2"

NPSM THREAD

1"-11 1/2

NPT THREAD

RPG01-118143

SPUD NUT KIT

(SV-4012/4016/4116/4128)

RPG01-118147

TAILPIECE NUT

RPG05-118142

VACUUM BREAKER KIT

RPG05-118161

“AA” BATTERY BOX

RPG11-118155

MANUAL OVERRIDE KIT

RPG11-118156

MANUAL OVERRIDE

INTERNAL KIT

RPG11-118157

MANUAL OVERRIDE

GASKET AND SEAL KIT

RPG11-118158

MANUAL OVERRIDE

COVER KIT

RPG20-118133

SENSOR AND VALVE

COVER KIT (SV-4012)

RPG20-118135

SENSOR AND VALVE

COVER KIT (SV-4016)

RPG31-118140

TAILPIECE PIPING

(SV-4012/4016/4116/4128)

RPG31-118148

CONTROL STOP TO

VALVE BODY PIPING

(SV-4012/4016/4116/4128)

RPG31-118163

INLET SUPPLY KIT

(SV-4012/4016/4116/4128)

RPG39-118160

SOLENOID REPLACEMENT

(SV-4012/4016/4116/4128)

RPG45-118145

SPUD GASKET AND SLIP RING

(SV-4012/4016/4116/4128)

RPG49-118150

O-RING & LOCK RING

FOR CONTROL STOP TO

VALVE BODY PIPE

RPG58-118152

CONTROL STOP

(SV-4012/4016/4116/4128)

RPG58-118153

CONTROL STOP

INTERNAL KIT

RPG58-118154

CONTROL STOP

BONNET, COVER,

& ADJUSTMENT SCREW

REPAIR PARTS

NOTE:

Regulations prohibit using replacement parts for this product that would increase the flushing volume beyond what is stated on the label.

As such, replacement parts are not designed or intended to be interchangeable with parts that would cause this product to exceed said flushing volume.

RPG05-118138

PISTON KIT

(SV-4012/SV-4128/SV-4016/SV-4116)

Summary of Contents for SV-4012







Search results

Summary of Contents for SV-4012

Reviews:

Related manuals for SV-4012

Brands by name

Popular brands

Speakman SV-4012, Installation Instructions Manual

Search results

Summary of Contents for SV-4012

Reviews:

Related manuals for SV-4012

Brands by name

Popular brands