South Bend Tools
For Machines Mfd. Since 10/21
Model SB1118
-33-
O P E R A T I O N
In MANUAL mode, the table can be moved with
the digital readout keypad.
The digital readout values can be expressed
either in millimeters or inches with the MM/
INCH key
MANUAL
SINGLE
PROG
STOP
QTY
RPM
DEG
7
8
9
F
4
5
6
1
2
3
+/-
0
.
START
MM
INCH
(see Figure 31). The light on this
key will show which measurement is active each
time the key is pressed.
Changing Digital Readout Values
Moving Table in MANUAL Mode
Moving Table in SINGLE Mode
In SINGLE mode, the table can be moved to a
target position with the digital readout keypad.
1.
Press MANUAL/SINGLE key
MANUAL
SINGLE
PROG
STOP
QTY
RPM
DEG
7
8
9
F
4
5
6
1
2
3
+/-
0
.
START
MM
INCH
to select
MANUAL mode. Light on key will blink.
2.
Press and hold "9" key
MANUAL
SINGLE
PROG
STOP
QTY
RPM
DEG
7
8
9
F
4
5
6
1
2
3
+/-
0
.
START
MM
INCH
to move table up;
release key to stop movement.
3.
Press
and hold 8 key
MANUAL
SINGLE
PROG
STOP
QTY
RPM
DEG
7
8
9
F
4
5
6
1
2
3
+/-
0
.
START
MM
INCH
to move table
down; release key to stop movement.
To move table in manual mode:
1.
Press MANUAL/SINGLE key
MANUAL
SINGLE
PROG
STOP
QTY
RPM
DEG
7
8
9
F
4
5
6
1
2
3
+/-
0
.
START
MM
INCH
to
select SINGLE mode. Light on key will not
illuminate.
2.
Press PROGRAM key
MANUAL
SINGLE
PROG
STOP
QTY
RPM
DEG
7
8
9
F
4
5
6
1
2
3
+/-
0
.
START
MM
INCH
. Light will blink
in target window.
3.
Use keypad to enter target value for table
position.
4.
Press ENTER key
MANUAL
SINGLE
PROG
STOP
QTY
RPM
DEG
7
8
9
F
4
5
6
1
2
3
+/-
0
.
START
MM
INCH
. Light on START key
MANUAL
SINGLE
PROG
STOP
QTY
RPM
DEG
7
8
9
F
4
5
6
1
2
3
+/-
0
.
START
MM
INCH
will blink.
5.
Press START key
MANUAL
SINGLE
PROG
STOP
QTY
RPM
DEG
7
8
9
F
4
5
6
1
2
3
+/-
0
.
START
MM
INCH
to move table to
target position.
Note:
To stop table movement before table has
reached target value, press STOP key
MANUAL
SINGLE
PROG
STOP
QTY
RPM
DEG
7
8
9
F
4
5
6
1
2
3
+/-
0
.
START
MM
INCH
. To
restart, perform Steps 1–5.
To move table in SINGLE mode:
Up to ten preset table positions can be stored
in permanent memory. On the keypad, these
positions are associated with the "0" through "9"
keys.
Adding/Subtracting Distances
In SINGLE mode, distances can be added to or
subtracted from the current position of the table.
To add/subtract distances:
1.
Press MANUAL/SINGLE key
MANUAL
SINGLE
PROG
STOP
QTY
RPM
DEG
7
8
9
F
4
5
6
1
2
3
+/-
0
.
START
MM
INCH
to
select SINGLE mode. Light on key will not
illuminate.
2.
Press +/- key
MANUAL
SINGLE
PROG
STOP
QTY
RPM
DEG
7
8
9
F
4
5
6
1
2
3
+/-
0
.
START
MM
INCH
. Light in target window
will blink.
— To add distance to current table position,
enter value using keypad.
— To subtract distance from current table
position, press +/- key
MANUAL
SINGLE
PROG
STOP
QTY
RPM
DEG
7
8
9
F
4
5
6
1
2
3
+/-
0
.
START
MM
INCH
again. A minus
sign will appear on left edge of target
window. Enter value using keypad.
3.
Press ENTER key
MANUAL
SINGLE
PROG
STOP
QTY
RPM
DEG
7
8
9
F
4
5
6
1
2
3
+/-
0
.
START
MM
INCH
. Light on START key
MANUAL
SINGLE
PROG
STOP
QTY
RPM
DEG
7
8
9
F
4
5
6
1
2
3
+/-
0
.
START
MM
INCH
will blink.
4.
Press START key
MANUAL
SINGLE
PROG
STOP
QTY
RPM
DEG
7
8
9
F
4
5
6
1
2
3
+/-
0
.
START
MM
INCH
to move table to new
location.
Note:
To stop table movement before table has
reached new target value, press STOP key
MANUAL
SINGLE
PROG
STOP
QTY
RPM
DEG
7
8
9
F
4
5
6
1
2
3
+/-
0
.
START
MM
INCH
.
To restart, perform Steps 1–4.
Saving Preset Table Positions
To save preset table positions:
1.
Press MANUAL/SINGLE key
MANUAL
SINGLE
PROG
STOP
QTY
RPM
DEG
7
8
9
F
4
5
6
1
2
3
+/-
0
.
START
MM
INCH
to
select SINGLE mode. Light on key will not
illuminate.
2.
Press the following keys one at a time:
"F" key
MANUAL
SINGLE
PROG
STOP
QTY
RPM
DEG
7
8
9
F
4
5
6
1
2
3
+/-
0
.
START
MM
INCH
, "5" key
MANUAL
SINGLE
PROG
STOP
QTY
RPM
DEG
7
8
9
F
4
5
6
1
2
3
+/-
0
.
START
MM
INCH
, "5" key
MANUAL
SINGLE
PROG
STOP
QTY
RPM
DEG
7
8
9
F
4
5
6
1
2
3
+/-
0
.
START
MM
INCH
.
3.
Press ENTER key
MANUAL
SINGLE
PROG
STOP
QTY
RPM
DEG
7
8
9
F
4
5
6
1
2
3
+/-
0
.
START
MM
INCH
. Light in top and
bottom windows will blink, and "ProG" will
appear in target window.
Digital Readout Buttons
