background image

                                                                        ST2523 Series Operation Manual                                                              Ver1.2 

 

Chapter 1  Introduction to Instrument, Unpacking and                                     

Installing 

Thank  you  for  your  purchase  and  use  of  our  products!  This  chapter  will  introduce  the  basic  instrument 
performance, which is followed by notes of unpacking and installing. 

Caution:  the  low  test  terminal  of  ST2523/A  is  connected  to  the  ground.  When  testing  other  device  or 
components  except  batteries,  or  sending  it  to Bureau  of  Standard Measurement for  calibration,  please 
plan your measuring setup accordingly. 

1.1  

Introduction to the Instrument 

With the rise of consumer electronics, smart phones, home appliances, electric vehicles emerge endlessly. All 
these products require batteries to work properly; quickly and accurately detecting the battery performance will 
directly affect the product performance. 
 
With profound electronic technology and extensive market research, we introduce the color LCD battery tester 
ST2523.  Its  superior  performance,  ease  of  operation,  beautiful  appearance  is  comparable  to  leading-edge 
products on the market. 
 

1.2  

OOBA (Out of Box Audit) 

Inspect the shipping container for damage after unpacking it. It is not recommended to power on the instrument 
in the case of a damaged container. 
If the contents in the container do not conform to the packing list, notify us or your dealer. 
 

1.3  

Power Connections 

( 1 )

 

Power Supply Voltage: 220 to 240 V   

( 2 )

 

Power Supply Frequency: 50 Hz. 

( 3 )

 

Power Supply Power Range: ≤ 30 VA. 

( 4 )

 

L  (line  wire),  N  (neutral  wire)  and  E  (earth  ground  wire)  of  the  power  supply  input  socket  should 
correspond to the power plug of the instrument. 

( 5 )

 

The instrument has been carefully designed for decreasing noise jamming caused by the input in AC 
power terminal, but it is also recommended to use it in the environment of low noise. If noises cannot 
be avoided, install a power filter please. 

 

WARNING:

  To  avoid  injury  to  personnel  and  damage  to  the  instrument  resulting  from  electric 

shock, do ensure that the earth ground wire is properly grounded.

 

 

Summary of Contents for ST2523








































































Reviews: