background image

more of the following measures:

• Reorient or relocate the receiving antenna
• Increase the separation between the equipment or devices
• Connect the equipment to an outlet other than the receiver's
• Consult a dealer or an experienced radio/TV technician for assistance

FCC Caution: Any change or modification to the product not expressly approved by SLH could void
the user’s authority to operate the device.

End of Lifetime

When the useful lifetime of this product has been reched, it must be disposed of pro-
perly. Electronic devices must not be placed in domestic waste. Consult your local
authorities to find the nearest collection point of used electric and electronic devices.
SOUNDLIGHT is a WEEE registered company (Reg No. DE58883929).

Service

There are no parts within the DMX relais card 3212R-H which require the user's attention. Should
your unit require servicing, please send it to the factory, freight paid.

Accessories

Setting the DMX start address, the DMX personality, or the DMX HOLD mode and other parame-
ters requires a suitable DMX RDM controller or a start address board. We recommend these devi-
ces:

DMX START ADDRESS BOARD 3000P

Address board to set start address, personality and DMX HOLD
mode.

Address boards are not contained with delivery and must be or-
dered separately.

For more info refer to:
www.soundlight.de/produkte/3000p

DMX RDM CONTROLLER GET/SET USBRDM-TRI

The USBRDM-TRI Interface connects via USB and comes with
RDM controller software  „GET/SET“. This software allows to admi-
nister all RDM supported functions of the Relay module.

The USBRDM-TRI Mk2 can be inserted into a existing DMX line
(e.g. from light control desk to fixtures) to add DMX RDM functionality for legacy setups.

For more info refer to: www.soundlight.de/produkte/usbrdm-tri2

Summary of Contents for 3212R-H











Reviews: