background image

Applications

The DMX relay decoder  3212R-H is ideally suited for all kinds of signal switching applications. It
features twelve potential-free high-power N.O. output  contacts and features high noise immunity.
Applications include remot control operations (e.g. smoke machine, bells, contacts, audio recor-
ders, door openers, halogen lamps, mirror balls etc). The 3212R-H is a universal tool for stage, tv
and theatre, as well as live acts. When actions have to be triggers by DMX, the 3212R-H comes in
handy.

The DMX relay 3207R-H is intended for use in dry environments. It must be instal-
led in a  suitable electrical cabinet. The operating conditions (see chapter „Techni-
cal Data“ must be met.

UNPACKING

Please unpack carefully and check that all items are intact. When leaving our factory, the card has
been in good condition. In case of damage during transport please notify the carrier immediately.
Please note that individual deadlines may apply to claim transport damages. We will only be able
to replace goods damaged during transit if we receive a written and signed confirmation issued by
the freight forwarder. Make sure you receive such a document and send to us a.s.a.p.

When unpacking, you should identify these items:

*

the interface  3207R-H RDM

*

this manual

Please note that a start adderess board (3000P) is NOT included with DIN rail mount devices.
A programming adaptor (required to set DMX start address and operating options) must be ordered
separately. If  you already have it, there is no need to buy again:  the start address board can be
used for all our DMX interfaces, pcb and DIN rail mount alike. Alternatively, all parameters can be
set or modified remotely using a suitable DMX RDM controller.

Connectors

The decoder 3212R-H consists of 6 terminal blocks. Terminals
are based on screwless WAGO cage clamp technology, which
prevents loose connections and guarantees safe electrical con-
tact at all times. Use a standard

 flat blade

 screw driver and press the le-

ver to open the terminal, insert wire and release. Do 

not

 use a philipps or

pozidrive screwdriver to prevent damage ! Though both, solid and strand-
ed wires may be used we recommend to use stranded wires in combina-
tion with isolated ferrules whenever possible.

SI

 Peugruppe verwendet empfindliche elektronische Komponente

Please refer to the connector location outlined on next page.

The 3212R-H consists of these connectors:

Summary of Contents for 3212R-H











Reviews: