Sound Devices PIX 250i User Manual And Technical Information Download

Page: 80 / 84

PIX 250i User Guide and Technical Information

v. 2.00

Features and specifications are subject to change. Visit www.sounddevices.com for the latest documentation.

Specifications

Timecode Inputs / Outputs

•  SDI Input BNC
•  SDI Output BNC
•  HDMI Input Jack (Sony protocol)

• Timecode Input BNC
• Timecode Output BNC

Sync Output

• Analog bi-, tri-level sync / Genlock
• Wordclock (Square wave, 48 kHz sampling rate, 3.3vp-p, 75 ohm)

Sync Input

• Analog bi-, tri-level sync / Genlock
• Wordclock (Square wave, 48 kHz sampling rate, 3.3vp-p, 75 ohm)

Control

RS-422

Machine Control

Ethernet

Web-based control of settings and transport (PIXNET)

GPIO

GPIO on 8 pins, Phoenix connector

Keyboard

USB Keyboard

Front-panel USB host. Keyboards without hubs acceptable

Power

External

• 10–27V, 60W max, via locking 4-pin XLR connectors (pin-1 = ground, pin-4 = +).

See

Powering

• Primary connector powers unit. Secondary connector switched to when Primary is discon-

nected.

Physical

Size (H x W x D)

3.3” x 8.6” x 10.3” (8.4 cm x 21.8 cm x 26.2 cm)

Weight

6.3 lbs

Operating Temperature

-10° C to +40° C

Summary of Contents for PIX 250i





















































































Search results

Summary of Contents for PIX 250i

Reviews:

Related manuals for PIX 250i

Brands by name

Popular brands

Sound Devices PIX 250i, User Manual And Technical Information

Search results

Summary of Contents for PIX 250i

Reviews:

Related manuals for PIX 250i

Brands by name

Popular brands