Sota BT6pro Manual Download Page 9

• The SOTA units are consumer products designed to be used as part of a Wellness Lifestyle • The SOTA units are not medical devices nor are they 

intended to diagnose, treat or cure any medical or health condition • The use, safety or effectiveness of the SOTA units has not been approved by any 

government agency • Please consult a health practitioner for any medical or health condition • Results using the SOTA Products will vary for each 

person • Please note that all purchases of SOTA Products are deemed to be made in Penticton, BC, Canada •

© 2001-2018 SOTA Instruments Inc. 

Page 9 of 9 

|

 www.sota.com

Designed, Engineered and Made in Canada.

The Bio Tuner Model BT6pro Manual

ELECTRICAL SPECIFICATIONS

POWER REQUIREMENTS

Use a 9–Volt Alkaline battery for proper operation.

OPTIONAL POWER INPUT

The Bio Tuner can also be operated using NiMH rechargeable batteries. When 

purchasing rechargeable batteries, it is suggested to take the unit with you to ensure 

the batteries will fit the enclosure. 

OUTPUT SPECIFICATIONS

Maximum <1.5mA Peak ~40 Volts Peak-Peak into typical 4k ohm load. Minimum 

<~10uA, 10 Volt Peak-Peak at lowest setting. Output impedance ~20k ohm.
1,000 Hz (+/- 1%) pulse-modulated by 111.11 Hz (+/- 1%). Waveforms are Quartz 

Crystal-Controlled for precise frequency output. There is also a broad range of 

harmonic frequencies delivered in each pulse as observed on a frequency domain 

spectrum analyzer.
Pulses are an alternating current (AC) output with no direct current (DC) or offset 

bias. Output is transformer coupled so that no DC can appear at electrodes.

REPLACEMENT ACCESSORIES

To replace your accessories, contact your supplier. 

WARRANTY

The Bio Tuner Model BT6pro is covered by a three (3) year limited warranty. Please 

keep proof of purchase. Warranty is void if the failure is due to abuse or negligence. 

SOTA reserves the right to make changes to the Bio Tuner without obligation. 

REPAIRS 

Please contact your supplier for return instructions. For information about your closest 

repair depot, contact [email protected] or call Toll-Free: 1.800.224.0242 (Canada & 

USA) or 1.250.770.2023.    

Summary of Contents for BT6pro










Reviews: