7
XTL-W7000
9
VIDEO2 IN
VIDEO OUT
TV main unit
Film antenna
qf
To the commercially avilable
Back Camera or Navigation
System
Antenna input
cable
qg
TV
antenna
amplifier
unit
qd
RCA interconnects (not supplied)
DVD player
etc.
Car audio, rear
passenger TV or
monitor etc.
This terminal is not used in this case.
Black
Genuine Car
audio
To a metal point of the car
To the +12 V power terminal which
is energized at all times
Yellow
Fuse (5A)
Purple/white
To the +12 V power terminal of the
back lamp lead of car
Orange/white
To the +12 V power terminal which is
energized in the accessory position of the
ignition key switch.
Be sure to connect the black ground lead
first.
Light green
Tap
7
To a car’s illumination signal
*
2
Tap
7
Parking brake switch lead of car
To a metal point of the car
To the +12 V power
terminal which is
energized in the
accessory position of the
ignition key switch.
Be sure to connect the
black ground lead first.
*1 An adaptor (optional) may be necessary for your car and
car audio system. In such case, consult your dealer.
*2 First connect the black ground lead, then connect the
orange/white striped, yellow and red power input leads.
Red
from a car antenna
*
1
Connecting without Sony BUS system
Black
Red
Antenna connector
*
1
10
VIDEO2 IN
BUS AUDIO IN
VIDEO OUT FRONT
CONTROL
VIDEO OUT
TV main unit
Film antenna
qf
To the commercially available
Back Camera or Navigation
System
Antenna input
cable
qg
TV
antenna
amplifier
unit
qd
Black
To a metal point of the car
To the +12 V power terminal which
is energized at all times
Yellow
Fuse (5A)
Purple/white
To the +12 V power terminal of the
back lamp lead of car
Orange/white
To the +12 V power terminal which is
energized in the accessory position of the
ignition key switch.
Be sure to connect the black ground lead
first.
Light green
To a car’s illumination signal
*
2
Parking brake switch lead of car
Red
This terminal is not used in this case.
Yellow
Red
White
Yellow
Red
White
2
RCA interconnects (0.5m)
3
RCA interconnects (0.5 m)
Rear passeger TV
or monitor etc.
Connecting with Sony BUS system
To a metal point of the car
To the +12 V power terminal
which is energized in the
accessory position of the
ignition key switch.
Be sure to connect the black
ground lead first.
Sony BUS Master-unit (equipped
with the TV control function)
*
1
*1 Sony BUS Master-unit (equipped with the TV control
function) will come in 2005.
*2 First connect the black ground lead, then connect the
orange/white striped, yellow and red power input leads.
Tap
7
Tap
7
RCA interconnects (not supplied)
Black
Red
11
Installation angle
The unit should be installed within an
angle of 30 degrees from horizontal. If
this angle is exceeded, the monitor may
not open up or retract properly.
Note
Keep the units and connection cables
apart.
The TV main unit and the amplifier unit
qd
should not be in close proximity.
2
Installing the Main Unit
After all connections are made, install the main unit to the
dashboard.
Before installation
This unit is designed to be completely safe, but if not installed
correctly, it can cause accidents. Be sure to verify the following
points before installation.
Install the main unit to the in-dash location, and the amplifier unit
under the navigator’s seat, etc.
• If the monitor in the opened position is close to a air-
conditioning outlet, the outlet should be closed.
• Install the unit so that the monitor when opened up will not
block access to the hazard switch or other important controls.
• Do not install the unit (monitor) in locations which may be
subject to excessively low or high temperatures. (Otherwise the
unit may be deformed and the LCD may be damaged.)
Exposure to direct sunlight can also lead to high temperatures
and should be avoided.
Selecting the installation location
1
Set the ignition key to OFF or remove it.
2
Place the units in their intended mounting
locations to check the cable length and monitor
installation conditions.
Installation procedure precautions
• Perform the installation carefully. Dropping the unit or
otherwise subjecting it to strong impact or force may deform
the chassis, resulting in failure of the monitor loading
mechanism or other defects.
N
N
T
T
N
T/N
T/N T/N
T
• To allow for proper opening and closing of the monitor, there
must be a clearance of at least 167 mm between the closest
position of the shift lever and the mounting surface for the unit.
• In some cases, the shift lever may touch the monitor when
moved to a certain position. Make sure that there is no
obstruction to driving operations.
• When installing this unit together with other car audio
equipment (single DIN slot size) in a stacked configuration,
install the TV main unit on top.
Shift lever
At least 167 mm
from mounting
surface
12
Removing the bracket
Before installing the unit, remove the bracket from the unit.
1
Insert two release keys
qa
together into the unit
and the bracket
8
until they click.
2
Pull down the bracket
8
, then pull up the unit to
separate.
m
,
8
qa
Face the hook
inwards.
