Sony PCG-8A8M Page 64 User Manual Download

Page: 64 / 119

Sony Notebook

User Guide

Connecting peripheral devices

n N

Disconnecting your computer from the port replicator

To disconnect your computer from the port replicator, proceed as follows:

Turn off the computer and the connected peripherals.

Pull the levers on each side of the port replicator to disconnect the computer from the port replicator.

Lift the notebook away from the port replicator.

Close the port replicator connector cover on the bottom of your computer.

✍

It is extremely important to close the port replicator connector cover after removing your computer from the port replicator. If the cover is left open,
dust may get inside and damage the computer.

To disconnect your port replicator completely from the mains voltage, unplug the AC adapter.

Summary of Contents for PCG-8A8M
























































































































Search results

Summary of Contents for PCG-8A8M

Reviews:

Related manuals for PCG-8A8M

Brands by name

Popular brands

Sony PCG-8A8M, User Manual

Search results

Summary of Contents for PCG-8A8M

Reviews:

Related manuals for PCG-8A8M

Brands by name

Popular brands