background image

SERVICE MANUAL

Conditions of Use:

(1)  Please use this information only for the purpose of performing repair, maintenance and/or con

fi

 guration services of the Sony products (hereinafter the “Repair services”) under the ser-

vice agreement entered into with the Sony group company (hereinafter the “Service agreement”). Using this information for any purpose other than the purpose described foregoing is 
forbidden.

(2)  Only the Authorized Servicer’s of

fi

 cers, employees or subcontractors (including their of

fi

 cers and employees) whose duties justify a need-to-know and who have agreed to hold 

con

fi

 dential this information (collectively hereinafter the “Permitted users”) are permitted to access and use this information. To disclose or disseminate to any person other than the 

Permitted users is forbidden.

(3)  Destroy or erase any and all portion of this information promptly in an irrecoverable and secure fashion after achieving the purpose described in Section (1) above.
(4)  Do not copy, replicate, reproduce, alter, translate, transmit, sell, lease, or distribute this information in whole or in part without the prior written permission of the author.
 

(Notwithstanding foregoing, it is permitted to copy and distribute this information to the Permitted users.)

(5)  Please notify immediately any leakage, loss, theft, misappropriation, or other misuse of this information by e-mail to the following address:
 

 

[email protected]

(6)  In addition to the above, the terms and conditions of the Service agreement shall be applied to using this information.

Revision of Information:

This information may be changed or updated at any time without any prior notice. Please con

fi

 rm that this information is up-to-date before using it.

Sony CONFIDENTIAL

For Authorized Servicer

Sony Home Entertainment &

 Sound Products Inc.

9-896-611-03

2020B33-1

© 

2020.02

CAUTION

Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.

注意
如果电池更换不当会有爆炸危险
只能用同样类型或等效类型的电池来更换

CAUTION

Risk of explosion if battery is replaced by an incorrect type.
Dispose of used batteries according to the instructions.

Note:

Be sure to keep your PC used for service and 
checking of this unit always updated with the 
latest version of your anti-virus software.
In case a virus affected unit was found during 
service, contact your Service Headquarters. 

NW-A100TPS/A105/

A105HN/A106HN

SYS SET

2020/02/27 22:57:21 (GMT+09:00)

Summary of Contents for NW-A100TPS






























































Reviews: