1-7
30
Press
v
/
V
on the control button to adjust the volume.
Press DISPLAY/LCD BACK LIGHT ON/OFF to turn on/off the indicators on the
LCD screen.
See page 107 for a detailed description of the indicators.
Adjusting the volume
The indicators on the LCD screen during moving image playback
v
/
V
on the
control button
BBBB
P
lay
b
a
ck
31
Preparation for viewing images
using a computer
When your disc drive does not conform to 8 cm CD, use the supplied 8 cm CD
adaptor.
Using the supplied 8 cm CD adaptor
1
Slide the disc into the inner groove and under two of the tabs on
the inner circle of adaptor in the numbered order.
2
Pull the third tab out away from the disc and the disc will slip into
place. Release the third tab and the disc will be held firmly in place.
1
2
Printed side of the disc (The other side is
recordable side.)
Printed side of the adaptor (SONY is printed
on this side and the other side is the luster
side.)
32
Notes
•
The supplied adaptor may not be used with your disc drive. For details, refer to the operating
instructions of the disc drive.
•
Use the adaptor at a low-speed (8-speed or lower).
•
Do not place the adaptor under direct sunlight or near the heat.
•
The adaptor is only used with Mavica discs. This cannot be used with other 8 cm CD-Rs/CD-
RWs.
You can play back the disc recorded with this camera on CD-ROM drives. You have
to execute the finalization before viewing images on a CD-ROM drive. A disc that
has not been executed the finalization cannot be read with CD-ROM drives.
What is finalization?
•
The finalization is required to view images on a CD-ROM drive.
•
You can record new images on the finalized disc if you execute the initialization on
it again. The initialization will be automatically executed when the finalization is
executed using the camera. You have to execute the finalization to view new images
on a CD-ROM drive. Each time you execute the finalization, approximate 13 MB of
the disc will decrease. We recommend that you execute the finalization onto
compiled data at a time.
•
You can execute the finalization onto the disc later, even if you remove it from the
camera.
•
The CD-ROM drive must conform to the MultiRead type to read the disc that was
finalized.
3
Check that the disc is set correctly in the grooves of the adaptor,
that all the tabs are even with the surface of the adaptor, and that
the disc is not protrude from the adaptor.
Preparing for viewing images on CD-ROM drives (FINALIZE)
If the tabs protrude, press them back down
into place. Otherwise, it may cause
malfunction of your disc drive.
BBBB
P
lay
b
a
ck
33
Executing the finalization
To cancel the finalization
Select [CANCEL] with
V
on the control button in step
4
or
5
, then press the center
z
. Once the finalization starts, you cannot cancel it.
1
Set the mode dial to SET UP.
The setup screen appears on the LCD screen.
2
Select [
] (DISC TOOL) with
v
/
V
on the
control button, then press
B
.
3
Select [FINALIZE] with
v
/
V
on the control
button, then press
B
B
B
B
.
4
Select [OK] with
v
on the control button,
then press
z
z
z
z
.
“FINALIZE PLACE ON LEVEL SURFACE”
appears on the LCD screen. Be sure to avoid any
vibration during the finalization.
5
Select [OK] with
v
on the control button, then press
z
z
z
z
.
Finalization starts and the disc remaining indicator changes from
to
, or
from
to
.
SELECT
DISC TOOL
FINALIZE:
FORMAT:
INITIALIZE:
UNFINALIZE:
DISC TOOL
FINALIZE:
FORMAT:
INITIALIZE:
UNFINALIZE:
OK
O K
CANCEL
OK
FINALIZE
PLACE ON LEVEL SURFACE
O K
READY?
CANCEL
FINALIZE
AVOID ANY VIBRATION
READY TO FINALIZE
FINALIZE
AVOID ANY VIBRATION
FINALIZE IN PROGRESS
FINALIZE
FINALIZE COMPLETE
