Sony HDCU-F950 Installation And Maintenance Manual Download Page 57

Page: 57 / 62

3-7 (E)

HDCU-F950 IMM

* System Diag 2/3 *

CAMERA Cable Connect

Data OK

Power ON

RCP/CNU Cable Connect

Data OK

Power OFF

PANEL Cable Open

Data --

Power ON

1
2

3
4
5

7
8

* System Diag 3/3 *

Intercom

CAMERA CH1 PROD

MIC ON

CH2 PROD

MIC ON

CAMERA MIC Gain

CH1 60dB Local

CH2 60dB Local

Page 6

System Diag (2/3) Display

No.

Contents

State of camera cable connection (Open/Connect)

Existence of data from the camera (

/Wait/Sense/OK)

The communication with the camera cannot be
established.

Wait :

The communication with camera is in the wait
state.

Sense : The communication with the camera is being

established.

State of the power supply of the camera (ON/OFF)

State of cable connection of the RCP/CNU connector on
the rear panel of the unit (Open/Connect)

Existence of the data from the RCP/CNU connector on
the rear panel of the unit (

/Wait/Sense/OK)

The communication with the equipment
connected to the RCP/CNU connector cannot be
established.

Wait :

The communication with the equipment
connected to the RCP/CNU connector is in the
wait state.

Sense : The communication with the equipment

connected to the RCP/CNU connector is being
established.

Power is supplied or not to the RCP/CNU connector on
the rear panel.
ON :

30 V power is supplied for RCP.

OFF :

Power is turned off.

State of cable connection with the front panel (Open/
Connect)

Existence of the data from the front panel (

/Wait/

Sense/OK)

The communication with the equipment
connected to the PANEL connector cannot be
established.

Wait :

The communication with the equipment
connected to the PANEL connector is in the wait
state.

Sense : The communication with the equipment

connected to the PANEL connector is being
established.

Power is supplied or not to the front RM panel.
ON :

30 V power is supplied for the front panel.

OFF :

Power is turned off.

Page 7

System Diag (3/3) Display

No.

Contents

Setting state of the intercom channel 1 of the camera
side (ENG/PROD)

Setting state of the intercom channel 2 of the camera
side (ENG/PROD)

Gain and control state of the microphone circuit of the
camera side (Remote/Local)

Summary of Contents for HDCU-F950































































Search results

Summary of Contents for HDCU-F950

Reviews:

Related manuals for HDCU-F950

Brands by name

Popular brands

Sony HDCU-F950, Installation And Maintenance Manual

Search results

Summary of Contents for HDCU-F950

Reviews:

Related manuals for HDCU-F950

Brands by name

Popular brands