Sony HDCU-F950 Installation And Maintenance Manual Download Page 60

Page: 60 / 62

3-10 (E)

HDCU-F950 IMM

* ROM Version *

CHU HDC-F950

1.20DM01

CCU HDCU-F950

1.02

MSU MSU-700A/750

1.10

Page 14

ROM Version Dispaly

Displays the ROM versions of the unit and the peripheral
equipment of the unit.

No.

Contents

Displays the ROM version of the HDC-F950.

Displays the ROM (IC510 and IC553 on the AT-149A
board) version of the HDCU-F950.

Displays the ROM version of the equipment that is
connected to the RCP/CNU connector on the rear panel
of he HDCU-F950.

* Slot-5 Diag *

Front: FC

IN :1080/59.94I

OUT :1080/59.94I

PLD V1.00 Config Done

Mode Normal

Rear: HIF

Page 12

Slot-5 Diag Dispaly

Displays the details of self-diagnosis of the FC-94 board of
the unit.

No.

Contents

State of the MAIN INPUT signal format of the frame
converter

State of the conversion format of the frame converter
MAIN OUTPUT signal

Displays the state of the PLD (IC200 on the FC-94 board)
version and PLD. (Config Done/Config NG)
Config Done : PLD (IC200 on the FC-94 board) started

correctly.

Config NG :

PLD (IC200 on the FC-94 board) did not
start correctly.

State of the operation mode on the FC-94 board (Normal/
Test)

Displays when the HIF-16 board is installed in the rear
correctly.

* Slot-6 Diag *

Front: None

Rear: None

Page 13

Slot-6 Diag Dispaly

Displays the details of self-diagnosis of the circuit board
that is mounted in the sixth slot from the left of the front
side of the unit.

No circuit board is installed at present.

Summary of Contents for HDCU-F950































































Search results

Summary of Contents for HDCU-F950

Reviews:

Related manuals for HDCU-F950

Brands by name

Popular brands

Sony HDCU-F950, Installation And Maintenance Manual

Search results

Summary of Contents for HDCU-F950

Reviews:

Related manuals for HDCU-F950

Brands by name

Popular brands