Sony HDCU-F950 Installation And Maintenance Manual Download Page 54 | Manualshive

Page: 54 / 62

background image

3-4 (E)

HDCU-F950 IMM

The contents of the pages displayed on the HD monitor (or
SD analog monitor) are as follows.

Page

Title

0

Displays OFF (CHARACTER button
OFF)

1

Camera Lens/Filter Status

2

Camera Status

3

System Status

4

Diagnosis

5

System Diag 1/3

6

System Diag 2/3

7

System Diag 3/3

8

AT Diag

9

AVP Diag

10

DTX Diag

11

DRX Diag

12

Slot-5 Diag

13

Slot-6 Diag

14

ROM Version

S202

S203

DRX

PO

WER

CHARA

CTER

60

50

48

540P

REW

FF

PsF

AB

C

1

2

3

4

5

CHARACTER switch

DRX-1A board (A side/panel side)

3-3. Character Display Function

This unit has the built-in character generation circuit. The
character information such as the settings, state and self-
diagnosis of the unit can be mixed with the HD SDI video
signal. The mixed signal can be output from the MONI
OUT (DRX-1A board output) and the HD SDI OUT (FC-
94 board output) connector respectively. They can be
displayed on the HD monitor.
The character MIX function can be forcibly turned OFF by
turning OFF S202-4 (HD SDI) on the DRX-1A board.

Required equipment

.

HD monitor

Sony BVM-D20F1U or equivalent

.

Remote control unit

Sony RCP-700 series

.

HDVS camera system

HDC-F950

Operating procedure

In order to show the setting, the state and the self-diagnosis
display on the HD monitor, press the CHARACTER
button of the RCP so that the button lights, or operate the
CHARACTER switch on the panel surface of the DRX-1A
board.
To change the page, press the CHARACTER button of the
RCP. The page can also be changed by pressing the
CHARACTER switch on the panel surface of the DRX-1A
board panel.
When the CHARACTER button of the RCP (or CHAR-
ACTER switch on the panel surface of the DRX-1A board)
is kept pressed, the pages are changed continuously. After
all the pages are displayed, the cycling display stops on the
final page and the CHARACTER button of the RCP goes
off. To display the character information again, press the
CHARACTER button of the RCP.

n

The first page is blank. When selecting the first page, the
display of characters is OFF.

«
...
52
53
54
55
56
...
»

Summary of Contents for HDCU-F950































































Reviews:

No comments

Related manuals for HDCU-F950

Brand: Tachyon Pages: 13

Brand: D-Link Pages: 41

Brand: ViewSonic Pages: 2

Brand: Concord Camera Pages: 57

Brand: VISIONARY DESIGNS Pages: 2

Brand: Prestigio Pages: 42

Brand: Foxtech Pages: 10

Brand: AXIOMTEK Pages: 56

Brand: Yada Pages: 24

ELVOX TVCC 46534.037BP

Brand: Vimar Pages: 4

Brand: Sungale Pages: 43

Brand: Solutions Pages: 31

Brand: Blaupunkt Pages: 61

ARTCAM-2020UV-USB3

Brand: ARTRAY Pages: 15

Brand: Preco Pages: 5

Brand: GeoSlam Pages: 15

Brand: GE Pages: 60

ZenFlash AFLU002

Brand: Asus Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands