Sony Cyber-shot DSC-WX50 Service Manual Download Page 28

Page: 28 / 28

DSC-WX50_L2

3-1E

3. ASSEMBLY

Assembly-1:

Precaution During Speaker Installation.

Speaker
Harness

Rib

Route the speaker harness as shown below.

Assembly-2:

Precaution During of ST-269 Flexible Board.

Install the ST-269 flexible board.

ST-269 flexible board

Claws

Bosses

Assembly-3:

Installation Cautions of the LCD Cushion (150)

and LCD Window (150).

LCD Cushion (150)

LCD Window (150)

Cabinet Rear Assy

LCD Window (150)

Release paper

Apply LCD Cushion (150) to the LCD Window (150)
adjusting shape as shown in the figure.
And peel off the release paper of LCD Cushion (150).

Put the LCD Cushion (150) and LCD Window (150)
on the Cabinet Rear Assy.

LCD Window (150),
LCD Cushion (150)

Attach the Panel Module to the LCD Cushion (150).

LCD Window (150)

Panel Module

LCD Cushion (150)

LCD Window (150),
LCD Cushion (150)

Summary of Contents for Cyber-shot DSC-WX50





























Search results

Summary of Contents for Cyber-shot DSC-WX50

Reviews:

Related manuals for Cyber-shot DSC-WX50

Brands by name

Popular brands

Sony Cyber-shot DSC-WX50, Service Manual

Search results

Summary of Contents for Cyber-shot DSC-WX50

Reviews:

Related manuals for Cyber-shot DSC-WX50

Brands by name

Popular brands