background image

DSC-WX50_L2

1-12

5

6

Removal

1

2

3

4

Claws

Sensor

Sensor

Claw

Boss

Rib

Rib

Rib

Claw

Disconnect the Iris Flexible Board

from LF-115 Flexible Board.

LF-115 Flexible Board

Top View

FG Leaf

Spring

Boss

Claws

FPC Retainer

Back View

Gear B

(Black)

Gear D

(Black)

Gear A

(White)

Gear C

(White)

Naruto

Gear

Screws

Rear Mirror

Plate

Screws

Disengage the two claws and remove the FG Leaf Spring.
Remove the two Sensors.
Disengage the three claws and remove the FPC Retainer.

Remove the LF-115 Flexible Board.

Remove the four screws to detach the Rear Mirror Plate
Remove the Gear B (Black), Gear A (White), Gear C (White), Gear D (Black), and Naruto Gear.

1-10.

 TWO TUBE LUBRICATING BLOCK ASSY AND GROUP 1 FRAME REPLACING METHOD

7

8

9

Iris Flexible Board

Cutout

Main Assy (A)

Rotary Tube

Block Assy

3 Group Spring

3 Group Frame

Block Assy

Tube

Lubricating

q;

qa

Main Assy (B)

Tube Lubricating

Block Assy

Shield Ring (C)

Remove the 3 Group spring and remove the 3 Group Frame Block Assy..

Turn the Tube Lubricating to the TELE state and remove the Iris Flexible Board from the cutout.

Remove the Main Assy (A) in the WIDE state.

Remove the Main Assy (B).
Remove the Tube Lubricating Block Assy and the Shield Ring (C) from the Rotary Tube Block Assy.

The changed portions from
Ver. 1.1 are shown in blue.

Ver. 1.2 2012.03

Summary of Contents for Cyber-shot DSC-WX50





























Reviews: