![background image](http://html.mh-extra.com/html/sony/cas-1/cas-1_service-manual_420233024.webp)
CAS-1
24
SECTION 3
TEST MODE
Preparation:
Use the following remote commander for test mode of this unit.
Note 1:
It cannot operation the test mode with the remote commander of
this unit’s accessories.
Note 2:
If using a remote commander other than the remote commander
for test mode indicated below and there is no [AMP] button on
the remote commander, skip the operation of pressing the [AMP]
button.
Part No.
Description
1-492-049-11
REMOTE COMMANDER (RM-AAU168)
LED position:
4
3
5
2
6
1
7
BLUETOOTH standby
mode indicator LED
Status indicator LED
Input indicator LED
– Front view –
TEST MODE OUTLINE
It can enter the each test mode of this unit when transmitting the
test code to the main unit with remote commander in the status of
entering the service mode.
When main unit has succeeded in reception of test code from
the remote commander, BLUETOOTH standby mode indica-
tor LED lights up once for 100 ms, when main unit has failed
in reception of test code from the remote commander, BLUE-
TOOTH standby mode indicator LED
fl
ashes 10 times in 100
ms interval.
SERVICING MODE
1. Setting method of servicing mode
Procedure:
1. Press the [
?
/
1
] button to turn the power on.
2. Press the [AMP]
→
[
V
]
→
[
v
]
→
[
V
]
→
[
v
]
→
[
b
]
→
[
B
]
→
[1]
→
[2]
→
[3] buttons on the remote commander in order.
Note 1:
Press the each button in 150 ms or more interval, and perform the
all button operations in 10 seconds or less.
3. When entering the servicing mode, BLUETOOTH standby
mode indicator LED lights up once for 100 ms.
Note 2:
When it has failed in setting of servicing mode, nothing has
changed. Perform from step 1 again.
2. Releasing method of servicing mode
Disconnect the AC cord to turn the power off.
FIRMWARE VERSION DISPLAY
It can check the
fi
rmware version of system controller, NET-
WORK board and BLUETOOTH module.
Procedure:
1. Enter the servicing mode.
(Refer to “1. Setting method of servicing mode”)
2. Press the buttons on the remote commander that correspond to
each
fi
rmware version display modes in order, and transmit the
test code to the main unit (Refer to the following table).
Note:
Press the each button in 150 ms or more interval, and perform the all
button operations in 7 seconds or less.
Mode
Buttons of remote commander
System controller
fi
rm-
ware version display
[AMP]
→
[DISPLAY]
→
[0/10]
→
[1]
→
[0/10]
→
[1]
→
[ ]
NETWORK board
fi
rm-
ware version display
[AMP]
→
[DISPLAY]
→
[0/10]
→
[1]
→
[0/10]
→
[2]
→
[ ]
BLUETOOTH module
fi
rmware version display
[AMP]
→
[DISPLAY]
→
[0/10]
→
[1]
→
[0/10]
→
[3]
→
[ ]
3. When entering each
fi
rmware version display mode, all input
indicator LEDs ([ ], [A], [B]) light up, and it indicate the ver-
sion (VXX.XX) by lighting-up and lighting-off of status indi-
cator LEDs.
Each numeral of version is indicated in following order.
Major upper digit (LED lights up for 3.9 seconds)
→
All LEDs
light off (for 0.1 seconds)
→
Major lower digit (LED lights
up for 3.9 seconds)
→
All LEDs light off (for 0.1 seconds)
→
Minor upper digit (LED lights up for 3.9 seconds)
→
All LEDs
light off (for 0.1 seconds)
→
Minor lower digit (LED lights
up for 3.9 seconds)
→
All LEDs light off (for 0.1 seconds)
→
Return to former status
Refer to the following table about numeral of version that indi-
cated by lighting-up and lighting-off of status indicator LEDs.
Numeral
of version
Status indicator LED
1
2
3
4
5
6
7
0
●
●
●
●
●
●
●
1
○
●
●
●
●
●
●
2
●
○
●
●
●
●
●
3
○
○
●
●
●
●
●
4
●
●
○
●
●
●
●
5
○
●
○
●
●
●
●
6
●
○
○
●
●
●
●
7
○
○
○
●
●
●
●
8
●
●
●
○
●
●
●
9
○
●
●
○
●
●
●
○
: lighting-up,
●
: lighting-off
Summary of Contents for CAS-1
Page 34: ...CAS 1 34 MEMO ...
Page 97: ...MEMO CAS 1 17 ...