Sony BWU-100A Operating Instructions Manual Download Page 16 | Manualshive

Page: 16 / 48

background image

16

Connect the drive as follows.

Installing the drive as a second drive

Secondary
IDE connector

Primary
IDE connector

2

nd drive

Place the jumper in
the MASTER position.

1

st drive

Hard disk drive (usually)
MASTER

Drive

The following configuration is also possible.

Secondary
IDE connector

Primary
IDE connector

Place the jumper
in the SLAVE
position.

1

st drive

Hard disk drive (usually)
MASTER

2

nd drive

Drive

«
...
14
15
16
17
18
...
»

Summary of Contents for BWU-100A

















































Reviews:

No comments

Related manuals for BWU-100A

ThinkPad 43N3201

Brand: Lenovo Pages: 46

ThinkPad 40Y8626

Brand: Lenovo Pages: 58

ThinkCentre 41N5624

Brand: Lenovo Pages: 66

ThinkCentre 41N5626

Brand: Lenovo Pages: 72

ThinkPad 41N5643

Brand: Lenovo Pages: 46

ThinkPad 40Y8706

Brand: Lenovo Pages: 62

ThinkPad 40Y8710

Brand: Lenovo Pages: 68

Brand: Lenovo Pages: 70

Brand: Lenovo Pages: 6

Brand: Integra Pages: 68

OPTIONS P09N4108

Brand: IBM Pages: 34

Brand: FANGOR Pages: 16

Brand: Teac Pages: 42

Brand: IBM Pages: 68

Pavilion 8800 - Desktop PC

Brand: HP Pages: 20

Brand: HP Pages: 34

Brand: HP Pages: 21

Model 715/100 - Workstation

Brand: HP Pages: 150

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands