Sony BKDS-7017 Installation Manual Download Page 8

Page: 8 / 78

DVS-7150E IM

.....

Maintenance Manual Part 2
Volume 5 (Schematic diagrams 1 A through I)

Part number : 9-967-624-03

Supplement 3

Part number : 9-967-624-83

Volume 6 (Schematic diagrams 2 K through Z)

Part number : 9-967-625-02

Supplement 4

Part number : 9-967-625-84

Contents

This manual is organized by following sections.

Section 1

Installation

This section describes the operating environment, power supply, connectors, input

and output signals of connectors, and example of system connection.

Section 2

Installation of DVS-7150

This section describes the external dimensions and rack mounting.

Section 3

Installation of Control panel

This section describes the external dimensions, installation space to console, rack

mounting and replacement of key tops.

Section 4

Installation of Options

This section describes the installation of plug-in boards, combinations of optional

boards and installation of options.

Section 5

Confirmation in Installation

This section describes the switch settings on boards and LEDs description,hard

reset,confirmation of secondary power supply voltage and adjustment of operation

power for fader lever.

Section 6

Initial Set-up of System

This section describes the operation and saving of set-up data, installation of pro-

gram, set-up.

Summary of Contents for BKDS-7017















































































Search results

Summary of Contents for BKDS-7017

Reviews:

Brands by name

Popular brands

Sony BKDS-7017, Installation Manual

Search results

Summary of Contents for BKDS-7017

Reviews:

Brands by name

Popular brands