Sony BKDS-7017 Installation Manual Download Page 7

Page: 7 / 78

DVS-7150E IM

Purpose of this manual

This manual is the installation manual of Digital Video Switcher DVS-7150.

This manual is intended for use by trained system and service engineers, and

describes the information when installing DVS-7150.

Related manuals

The following manuals are prepared for DVS-7150.

The part numbers of these manuals as of Novemver, 1998 describe.

.....

User’s Guide (Supplied with BZS-7080)

This manual describes the application and operation of DVS-7150.

.....

Operation Manual (Supplied with DVS-7150)

This manual describes the overview, system configuration examples and specifica-

tions of options.

.....

Maintenance Manual Part 1 (Supplied with DVS-7150)

This manual describes the information for the periodic maintenance, and the

information for the service with predicated on the replacement of the principal

blocks and mounted circuit boards.

Part number : 3-201-448-01

.....

Maintenance Manual Part 2

The following manuals describe the detailed service information. For obtaining,

please contact your local Sony’s sale/service office.

All Supplements will publish at February, 1999.

Volume 1 (Block diagrams and Frame wirings)

Part number : 9-967-615-03

Supplement 4

Part number : 9-967-615-84

Volume 2
(Spare parts, Service overview and Replacement of main parts)

Part number : 9-967-616-03

Supplement 5

Part number : 9-967-616-85

Volume 3 (Semiconductor pin assignments)

Part number : 9-967-617-03

Supplement 3

Part number : 9-967-617-83

Volume 4 (Board layouts)

Part number : 9-967-618-03

Supplement 4

Part number : 9-967-618-84

Manual Structure

Summary of Contents for BKDS-7017















































































Search results

Summary of Contents for BKDS-7017

Reviews:

Brands by name

Popular brands

Sony BKDS-7017, Installation Manual

Search results

Summary of Contents for BKDS-7017

Reviews:

Brands by name

Popular brands