manualshive.com logo in svg

Sony BKDS-7017, Installation Manual

Share
Download
Sony BKDS-7017 Installation Manual Download Page 59

5-7

DVS-7150E IM

5-1. Switch Settings on Boards and LEDs Description

5-1-3. BKDS-7017

1. CPU-246 Board

COP1 

(E3) :

This is used to select the mode corresponding to the synchronized signal that is connected to the
SWITCHER on the rear panel.  For DVS-7150, this is opened under normal status.

COP3 

(E3) :

This is used to select the RS-232C signal that is connected to the TERMINAL 2 on the rear panel.
Selection under normal status ; NOR side

Selection in the factory

; DBG side

S1 

(R10) : RESET switch

This switch is used to forcibly restart the SYSTEM by the hardware.  The unit is operated the same as the

operation when turning the POWER ON.

S2 

(R19) : ABORT switch

This switch is used for the adjustment in the factory.

S3 

(R10) : SUB ABORT switch

This switch is used for the adjustment in the factory.  If pressing this switch after selecting the S5 switch
on the CPU-246 board to the SUB CPU flash memory access protection mode, clean the content of the

flash memory for stored-program.

ON

1

2

3

4

5

6

7

8

Factory setting
S4, S5

CN8

CN17

CN9

CN10

CN1

CN6

CN4

CN5

CN3

D27

D26

D25

D24

D23

D22

D18

D17

D16

D6

D7

D2

D1

D295

D8

S3
S2
S1

CN19

CN12

CN14

CN18 CN21

CN16

COP2

COP1
COP3

CN15

CN13

IC39

S5

S4

D102

D112

D101

D111

CN20

CPU-246 board

(Component side/A side)

Summary of Contents for BKDS-7017















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands