Sony BKDS-2031 Installation Manual Download Page 6

Page: 6 / 110

DVS-7000AE IM

4. Installation of Options

4-1.

Installation of Plug-in Boards ..................................................................... 4-2

4-2.

Combination of Optional boards ................................................................. 4-4

4-2-1.

Function of Optional Boards ...................................................... 4-4

4-2-2.

Relation between Optional Boards and
Rear Panel Connectors ............................................................... 4-4

4-3.

Installation of Options for DVS-7000A ...................................................... 4-6

4-3-1.

Detaching and Attaching of Front Panel .................................... 4-6

4-3-2.

Inserting/Pulling Out of Plug-in Boards .................................... 4-7

4-3-3.

Installation of Optional Boards .................................................. 4-9

4-3-4.

Installation of BKDS-7690 (Redundant Power Supply Unit) .. 4-12

4-4.

Installation of Options for Control Panel .................................................. 4-13

4-4-1.

Opening and Closing of Panel .................................................. 4-13

4-4-2.

Turning On/Off the Power Switch ........................................... 4-14

4-4-3.

Installation of BKDS-7001 (Control Port Expansion Board) .. 4-15

4-4-4.

Installation of BKDS-7031 Track Ball .................................... 4-16

4-4-5.

Installation of Option Panels (BKDS-7030/7031/7032/7033) . 4-18

4-4-6.

Joining of BKDS-7075 (Control Panel Remote Adaptor) ....... 4-29

4-4-7.

Installation of BKDS-7090 (Redundant Power Supply Unit) .. 4-33

5. Confirmation in Installation

5-1.

Switch Settings on Boards and LEDs Description ...................................... 5-1

5-1-1.

DVS-7000A ................................................................................ 5-1

5-1-2.

BKDS-7133 ................................................................................ 5-6

5-1-3.

Control Panel .............................................................................. 5-6

5-1-4.

BKDS-7090 .............................................................................. 5-12

5-2.

Adjustment of Secondary Power Supply Voltage ..................................... 5-13

5-2-1.

DVS-7000A .............................................................................. 5-13

5-2-2.

Control Panel ............................................................................ 5-15

5-3.

Adjustment of Operation Power for Fader Lever ..................................... 5-17

6. Initial Set-up of System

6-1.

Operation and Saving of Set-up Data .......................................................... 6-1

6-2.

Installation of Program (BZS-7020A) ........................................................ 6-4

6-2-1.

Down Load of Program .............................................................. 6-5

6-2-2.

Initializing of Data on RAM ...................................................... 6-7

6-2-3.

Initializing of “Nonvolatile Memory” ........................................ 6-8

6-3.

Set-up .......................................................................................................... 6-9

6-3-1.

Confirmation of the Software Version ..................................... 6-10

6-3-2.

Setting of the Signal Format .................................................... 6-10

6-3-3.

Setting about the System .......................................................... 6-11

6-3-4.

Saving Set-up Data to Nonvolatile Memory ............................ 6-12

Summary of Contents for BKDS-2031















































































































Search results

Summary of Contents for BKDS-2031

Reviews:

Related manuals for BKDS-2031

Brands by name

Popular brands

Sony BKDS-2031, Installation Manual

Search results

Summary of Contents for BKDS-2031

Reviews:

Related manuals for BKDS-2031

Brands by name

Popular brands