3-3 (E)
BDX-N1000
3-2. Internal Indicators on Board
D501 (D-5) (green) : ATM receive status indicator
Lights up when receiving TS
1)
in the AAL1
2)
mode.
D600 (A-3) (yellow) : IC card status indicator
Lights up while firmware updating is in progress.
D601 (A-3) (green) : IC card status indicator
Lights up when the system starts up from the IC card.
D602 (A-3, A-4) (green) : Factory use only
D603 (A-3, A-4) (green) : Factory use only
3)
D604 to D609 (A-3) (green) : Factory use only
D900 (C-3, B-4) (green) : ATM receive status indicator
Lights up when the TS can be extracted from ATM cells.
D901 (C-3, C-4) (green) : ATM receive status indicator
Lights up when the TS packet length mode is set to 204 bytes.
D1000 (A-3) (green) : TS input status indicator
Lights up when the TS packet length mode is set to 204
bytes.
D1001 (A-3) (green) : TS input status indicator
Lights up when the TS can be extracted from the DVB ASI
input.
D1002 (A-3) (green) : Factory use only
D1003 (A-3) (green) : TS input status indicator
Blinks when TS is input to the MPEG BIT STREAM
INPUT connector on the rear panel.
D1100 (A-3, A-4) (red) : TS output status indicator
Lights up when an error occurs in the PCR
4)
(IC1100).
D1101 (A-3, A-4) (red) : TS output status indicator
Lights up when an error occurs in the PCR (IC1100).
D1102 (A-3, A-4) (red) : TS output status indicator
Lights up when an error occurs in the PCR (IC1100).
D1103 (A-3, A-4) (red) : TS output status indicator
Lights up when an error occurs in the PCR dejitter process-
ing (IC1100).
D1400 (E-6, D-6) (green) : Factory use only
D1401 (E-6, D-6) (green) : ATM send status indicator
Lights up when the rate of transmitting data is not
appropriate.
D1402 (E-6, D-6) (green) : ATM send status indicator
Lights up when the rate of transmitting data is not
appropriate.
D1403 (E-6, D-6) (green) : Factory use only
D1500 (B-6) (green) : TS input status indicator
Lights up when the TS can be extracted from the DVB ASI
input.
D1501 (B-6) (green) : ATM send status indicator
Lights up when the TS send is in progress in the AAL1
mode.
D1502 (B-6) (green) : ATM send status indicator
Lights up when the TS send is in progress in the AAL1
mode.
D1503 (B-6) (green) : Factory use only
3)
D1601 (C-2) (green) : 5 V power indicator
Lights up when 5 V power is supplied normally.
3)
D1606 (C-2) (green) : 3.3 V power indicator
Lights up when 3.3 V power is supplied normally.
3)
D1607 (E-2) (green) : 2.5 V power indicator
Lights up when 2.5 V power is supplied normally.
5)
D1609 (D-2) (green) : 5 V power indicator
Lights up when power of 5 V is supplied normally.
D6000 (A-3) (red) : TS input status indicator
Lights up when an error occurs in the PCR (IC1000).
D6001 (A-3) (red) : TS input status indicator
Lights up when an error occurs in the PCR (IC1000).
D6002 (A-3) (green) : TS input status indicator
Lights up when the PCR dejitter mode is ON.
D6100 (A-3, A-4) (green) : TS output status indicator
Lights up when the clock for the PCR dejitter is synchro-
nized in the clock of network.
