background image

 
 
 
 
 

Working Instruction, Mechanical

 

 

3/00021-1/FEA 209 544/83 A 

Company Internal 

 Sony Ericsson Mobile Communications AB 

19(37) 

 

3 Replacement 

of 

Mechanical 

Parts 

Equipment 

• 

ESD-gloves (cotton gloves) 

• 

ESD-wristband 

Instruction 

• 

Keep all contact surfaces clean of dirt and hand-grease 

3.1 System 

Connector 

Replacement of System Connector: Check end of Disassembly and Reassembly headings. 
Draw attention to Note comments. 

3.2 

Antenna Cover Complete 

Replacement of antenna cover complete: Check end of Disassembly and Reassembly 
headings. Draw attention to Note comments. 

3.3 Volume/Camera 

Keys 

& Internet Access Key 

Replacement of volume/camera keys & Internet access key: Check end of Disassembly and 
Reassembly headings. Draw attention to Note comments. 

3.4 Front 

Complete 

Replacement of front complete: Check Disassembly and Reassembly headings and draw 
attention to Note comments. 

3.5 Display 

Assembly 

Replacement of display assembly: Check Disassembly and Reassembly headings and draw 
attention to Note comments. 

3.6 Keyboard 

Foil 

Assembly 

Replacement of keyboard foil assembly: Check Disassembly and Reassembly headings and 
draw attention to Note comments. 

 

Summary of Contents for K700c






































Reviews: