Sony Ericsson K700c Working Instruction, Mechanical Download Page 7 | Manualshive

Page: 7 / 37

background image

Working Instruction, Mechanical

3/00021-1/FEA 209 544/83 A

Company Internal



Sony Ericsson Mobile Communications AB

7(37)

Step-by-Step Instructions

8

NOTE!
Do not touch the display glass with your fingers.

Lift the display with your fingers.

NOTE!
Be careful not to damage the display flexfilm
with the tweezers.

Remove the connector tape with a blunt pair of
tweezers.

NOTE!
Removed tape cannot be reused and must be
scrapped.

NOTE!
Be careful not to damage the FPC connector
clamp with the tweezers.

Open the FPC connector with a pair of tweezers.

NOTE!
Be careful with the display flexfilm.

Remove the display assembly from the FPC
connector with the flex film assembly tool.

«
...
5
6
7
8
9
...
»

Summary of Contents for K700c






































Reviews:

No comments

Related manuals for K700c

Univerge SV8100

Brand: NEC Pages: 4

Brand: Haier Pages: 24

Brand: Datawind Pages: 28

Brand: Uniden Pages: 24

Brand: Avaya Pages: 6

Brand: Allview Pages: 7

Brand: Nortel Pages: 20

Brand: Pacific GSM Pages: 8

Brand: Slider Pages: 27

Brand: SoftBank Pages: 2

Brand: BarcodeYes Pages: 12

Brand: V7 Pages: 20

Brand: Avaya Pages: 86

Brand: Alcatel Pages: 41

Brand: Haier Pages: 56

Brand: Haier Pages: 98

Brand: Lava Pages: 36

Brand: Lava Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands