manualshive.com logo in svg

Sony Ericsson K700c, Working Instruction, Mechanical, Page: 2 / 37

Share
Download
Sony Ericsson K700c Working Instruction, Mechanical Download Page 2

 
 
 
 
 

Working Instruction, Mechanical

 

 

3/00021-1/FEA 209 544/83 A 

Company Internal 

 Sony Ericsson Mobile Communications AB 

2(37) 

 

1 Disassembly 

Tools 

• 

Torque screwdriver, set to 18 Ncm 

±

 6%. Bits 6, NTZ 112 288 

• 

Flex film assembly tool NTZ 112 521 

• 

Blunt pair of tweezers, pair of tweezers 

• 

Screwdriver, width 3 mm 

• 

K700i/Front opening tool NTZ 112 540 

• 

Front opening tool NTZ 112 302/2 

• 

Dentist hook 

Equipment 

• 

ESD-gloves (cotton gloves) 

• 

ESD-wristband 

Instruction 

• 

Keep all contact surfaces clean of dirt and hand-grease 

• 

Removing Front Cover and Antenna Cover is very hard, due to that you do not know how 
much force that is needed unsnapping these parts. It also requires much technique 
removing these two parts. Training is very important, both by performing training in 
Learning Community and by hands on practice. 

 

 

Phone views 

 

Front view 

Back view 

 

 

 

Summary of Contents for K700c






































Reviews:

No comments