manualshive.com logo in svg

Sony Ericsson K700c, Working Instruction, Mechanical, Page: 10 / 37

Share
Download
Sony Ericsson K700c Working Instruction, Mechanical Download Page 10

 
 
 
 
 

Working Instruction, Mechanical

 

 

3/00021-1/FEA 209 544/83 A 

Company Internal 

 Sony Ericsson Mobile Communications AB 

10(37) 

 

 

Step-by-Step Instructions 

 

12  Antenna Cover removal: 

 
NOTE! 
The antenna cover should only be removed if 
there is a need of replacing the antenna cover 
itself, the frame or any of the following 
components located underneath the antenna 
cover: 
Volume and camera keys 
Internet access key 
Antenna flex 
Flexfilm volume and camera key 
Flexfilm camera light assembly 
Camera (for verifying that the camera is fitted 
properly) 
 
There is no need to remove the external antenna 
connector plug. 
 
Use a dentist hook or a flat screwdriver to 
remove the antenna cover. As long as you do not 
scratch the antenna cover or frame, you can use 
the tool that you feel most comfortable with. If 
you use a sharp tool be careful not to damage the 
snap hook. 
 
When removing the antenna cover the first time 
it is hard to predict the amount of force needed.  
Usually, as when removing the front cover, it 
requires more force then you think. 
 

If the phone is already disassembled, and 
there is a need for removing the antenna 
cover, it is OK to unsnap the antenna cover 
snap hooks from  the inside. 

 

 

 
 

 

Summary of Contents for K700c






































Reviews:

No comments