SOMFY animeo Operating Manual Download | Manualshive

Page: 10 / 55

background image

animeo KNX 4 AC Motor Controller

30.01.2019

WM/DRM 220-230 V AC



2011-2019, SOMFY Activites SA



50 avenue du Nouveau Monde



74300 Cluses



France

10/55

4.4 Manual learning-in of move times

The move and turn times per motor output can be set via local conventional push buttons. These settings
are possible only in the delivery state before the device has been programmed with the ETS. As soon as
the device with the ETS is programmed, the move times and turn times can no longer be set via local
conventional push buttons. When the device is unassigned by the ETS, the adjusting of the move times
and turn times via local conventional push buttons can be done again.

H

Alternatively to the conventional push buttons, the settings can also be done using the Somfy RTS Trans-

mitter and animeo RTS Radio Module (ref. 1860105). A setting using animeo KNX RTS Receiver (ref.
1860191) and Somfy RTS Transmitter resp. animeo EnOcean Receiver (ref. 1860220) or animeo KNX
EnOcean Receiver (ref. 1860229) und EnOcean Receiver is not possible!

4.5 Manual learning-in of the intermediate position 1

Intermediate position 1 can be learned-in individually per motor output via conventional local push but-
tons. At the same time, it is possible to carry out the intermediate position 1 via settings in the ETS pa-
rameters. Prior to this, the move and turn times must be learned-in!

H

Alternatively to the conventional push buttons, the settings can also be done using the Somfy RTS

Transmitter and animeo RTS Radio Module (ref. 1860105). A setting using animeo KNX RTS Receiver
(ref. 1860191) and Somfy RTS Transmitter resp. animeo EnOcean Receiver (ref. 1860220) or animeo
KNX EnOcean Receiver (ref. 1860229) and EnOcean Sender is possible through using the objects 64-67!

4.5.1 Save intermediate position 1 (IP1)

«
...
8
9
10
11
12
...
»

Summary of Contents for animeo
























































Reviews:

No comments

Related manuals for animeo

Brand: LAZER Pages: 13

Brand: Latento Pages: 60

Brand: Easy Quick Pages: 11

Brand: Radio Shack Pages: 2

Brand: X-pole Pages: 16

Brand: Manfrotto Pages: 2

Brand: Garmin Pages: 26

Brand: Garmin Pages: 33

Brand: Garmin Pages: 167

Line FP7000 Housing

Brand: Fantasea Pages: 5

Brand: Fantasea Pages: 5

Brand: Fancom Pages: 49

Brand: FANATEC Pages: 2

Brand: Manfrotto Pages: 2

Brand: Paradyne Pages: 2

Brand: La Crosse Technology Pages: 6

Brand: SECURENET Pages: 12

Brand: FujiFilm Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands