SOMA Pulsar-23 Manual Download Page 18 | Manualshive

Page: 18 / 172

background image

18

The Pulsar-23 Notebook : Reference & Guide

Envelope Generators

Each sound module has its own envelope generator which is integrally
configured to control volume. An envelope is triggered to control the
activation and shape of the sound as it develops over time. This is also
based on the duration of the trigger state. An AR - Attack / Release
envelope type is used in Pulsar-23, a model often used for drum sounds

.

NOTES

Sound Generators

2

A short trigger will initiate the ATT - Attack phase ramping up the sound level
and when the trigger is off the REL - Release time will control the audio ramp
down. This is typical for percussive hits and the envelope adjusted to suit.

A long trigger will initiate the ATT - Attack phase ramping up the sound level
and then will be sustained for the duration. When the trigger is off the REL -
Release will control the audio ramp down time. This is typical for drones and
pads and the envelope can also be adjusted to suit.

TRIG

ON

TRIG

ON

TRIG

OFF

TRIG

OFF

Attack Time

(ATT)

Attack Time

(ATT)

Sustain Level

with duration

based on trigger

Release Time

(REL)

Short Trigger

Long Trigger

Release Time

(REL)

«
...
16
17
18
19
20
...
»

Summary of Contents for Pulsar-23













































































































































































Reviews:

No comments

Related manuals for Pulsar-23

JUNIOR 5 PIECE DRUM KIT

Brand: Gear4music Pages: 8

Brand: Boss Pages: 6

Brand: Roland Pages: 13

LinkSign LCD 1x5

Brand: Topaz Pages: 9

Brand: Medeli Pages: 62

Brand: METASONIX Pages: 7

Brand: V-Drums Pages: 2

Brand: First Act Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands