SOLZAIMA SZM A PLUS 16 kW Instruction Manual Download

Page: 5 / 87

Solzaima

Solzaima's vision has always been to provide the cleanest, renewable and more cost-

effective energy. This is why we have been dedicated to manufacturing biomass

heating equipment and solutions for the past 45 years.

Due to its persistence and the unconditional support of its network of partners,

Solzaima is currently leader in the production of biomass heating systems, best

illustrated by its water heat recovery central heating units and its range of pellet stove

fires and boilers.

We deliver biomass heating units to approximately 20,000 homes every year. This

effectively demonstrates consumers' interest in more ecological and economic

solutions.

Solzaima was awarded the international Quality Certificate ISO 9001 and the

Environmental Certificate ISO 14001.

Summary of Contents for SZM A PLUS 16 kW
























































































Search results

Summary of Contents for SZM A PLUS 16 kW

Reviews:

Related manuals for SZM A PLUS 16 kW

Brands by name

Popular brands

SOLZAIMA SZM A PLUS 16 kW, Instruction Manual

Search results

Summary of Contents for SZM A PLUS 16 kW

Reviews:

Related manuals for SZM A PLUS 16 kW

Brands by name

Popular brands