Solectek skyway User Manual Download | Manualshive

Page: 30 / 52

background image

30

Voice Video Normal Background

Precedence

Class of Service

0

Best Effort

1

Background

2

Background

3

Best Effort

4

Video

5

Video

6

Voice

7

Voice

If there is no classification, (no VLAN and IP TOS 0) the packet falls under the Best Effort class. If
the packet has both VLAN and IP precedence values, the maximum of the two priorities (VLAN/IP) is
used.

The following table shows the mapping of class of service on various DSCP/TOS values.

Class of Service

IP

Precedence

(3 bits)

DSCP (6 bits)

TOS (8 bits)

Best Effort

0,3

0x0 (0)

0x0

«
...
28
29
30
31
32
...
»

Summary of Contents for skyway





















































Reviews:

No comments

Related manuals for skyway

Brand: MadgeTech Pages: 4

wM-Bus 868 USB Key

Brand: MADD Pages: 4

Brand: V2 Pages: 16

Brand: Teac Pages: 14

AquaTronics MS-850

Brand: ASA Electronics Pages: 5

Brand: Xoro Pages: 90

Brand: Nav TV Pages: 2

Brand: Hallicrafters Pages: 28

Brand: Raymarine Pages: 68

Brand: NAL Pages: 9

Brand: K1EL Pages: 53

Brand: Jensen Pages: 22

Brand: D+M Group Pages: 19

Brand: Wonde Proud Pages: 11

Brand: ZENEC Pages: 48

Brand: Icom Pages: 47

Brand: TANDBERG Pages: 14

Brand: Onkyo Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands