background image

solasfires.com

1

 WARNING

FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly could 

result in serious injury, death, or property damage.

—  Do not store or use gasoline or other flammable 

vapors and liquids in the vicinity of this or any 

other appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.
•  Do not touch any electrical switch; do not use any 

phone in your building.

•  Immediately call your gas supplier from a neighbor’s 

phone. Follow the gas supplier’s instructions.

•  If you cannot reach your gas supplier, call the fire 

department.

—  Installation and service must be performed by 

a qualified installer, service agency or the gas 

supplier.

DUE TO HIGH TEMPERATURES, THE APPLIANCE SHOULD BE 

LOCATED OUT OF TRAFFIC AND AWAY FROM FURNITURE 

AND DRAPERIES.
CHILDREN AND ADULTS SHOULD BE ALERTED TO THE 

HAZARD OF HIGH SURFACE TEMPERATURE AND SHOULD 

STAY AWAY TO AVOID BURNS OR CLOTHING IGNITION.
YOUNG CHILDREN SHOULD BE CAREFULLY SUPERVISED 

WHEN THEY ARE IN THE SAME ROOM WITH THE APPLIANCE.
CLOTHING OR OTHER FLAMMABLE MATERIAL SHOULD NOT 

BE PLACED ON OR NEAR THE APPLIANCE.
KEEP THE ROOM AREA CLEAR AND FREE FROM 

COMBUSTIBLE MATERIALS, GASOLINE, AND OTHER 

FLAMMABLE VAPORS AND LIQUIDS.

WARNING Improper installation, adjustment, services or 

maintenance can cause injury or property damage. Refer to 

this manual. For assistance or additional information, consult 

a qualified installer, service agency or the gas supplier.

TWENTY6 SLIM-LINE

 

BUILT-IN DIRECT-VENT 

GAS FIREPLACE with COOL ZONE

INSTALLER

: Leave this manual with appliance   |  

CONSUMER

: Retain this manual for future reference

INSTALLATION & OPERATION MANUAL

MODELS: 

BI-26N-SS, BI-26P-SS

Ce manual est disponsible en Francais sur demande.

This appliance may be installed in an aftermarket, permanently 

located, manufactured home (USA only) or mobile home, where 

not prohibited by local codes.
This appliance is only for use with the type of gas indicated on 

the rating plate. This appliance is not convertible for use with 

other gases, unless a certified kit is used.

Report #F19-217

HOT GLASS

WILL CAUSE BURNS.
DO NOT TOUCH GLASS

UNTIL COOLED.
NEVER ALLOW CHILDREN

TO TOUCH GLASS.

 

DANGER

A barrier designed to reduce the risk of burns 

from the hot viewing glass is provided with this 

appliance and must be installed for the protection 

of children and other at-risk individuals.

Summary of Contents for BI-26N-SS


























































Reviews: