Solas BI-26N-SS Installation & Operation Manual Download Page 54

Page: 54 / 57

SÓLAS

CONTEMPORARY FIRE

REPLACEMENT PARTS LIST

PART NAME

P/N

PART NAME

P/N

Pilot Head NG/LP

M26-501N / M26-501P

Burner Orifice (NG)

26N-509

Pilot Thermocouple*

M26-502*

Burner Orifice (LP)

26P-509

Pilot Injector (NG)

26N-503

Burner Glass Media – Clear

26-511

Pilot Injector (LP)

26P-503

Burner Module (NG)

26N-901

SÓLAS One-Touch Control Module

S-504

Burner Module (LP)

26P-901

Wall Touch Pad** (Optional)

WTP-1500

Firebox Enamel Panel – Rear

26-512

SÓLAS One-Touch Remote

S-507

Firebox Enamel Panel – Left

26-513

Gas Valve (Maxitrol)

M46-515

Firebox Enamel Panel – Right

26-514

TC Line Red

M46-701

Thermocouple Interrupter Block

M46-703

TC Line Yellow

M46-702

8-Wire Connecting Cable

M46-704

Glass Assy (including gasket & frame)

26-510

*This is a quick response thermocouple. Replace it only with SÓLAS Part Number M26-502.
**Not Compatible with SÓLAS Self-Calibrating Power Vent Kit

For Replacement Parts and customer service,

contact your SÓLAS Dealer or;
SÓLAS, LLC

452 Sunapee Street, Newport, NH 03773
P (603) 298-5169 [email protected]

Summary of Contents for BI-26N-SS


























































Search results

Summary of Contents for BI-26N-SS

Reviews:

Related manuals for BI-26N-SS

Brands by name

Popular brands

Solas BI-26N-SS, Installation & Operation Manual

Search results

Summary of Contents for BI-26N-SS

Reviews:

Related manuals for BI-26N-SS

Brands by name

Popular brands