background image

Potential equalization of the solar generator is 

prepared in the factory and is recommended. It 

can be carried out using the existing grounding 

bores on the long sides of the frame in accor-

dance with the valid local regulations.

Detailed view ground connection:

Fixing screw M4

Ring cable lug with ground cable

Toothed locked washer
Module  frame  with  hole  for 

grounding (ø 4.2 mm)
Spring washer

Nut

It is advisable to install lightening protection in exposed locations. The solar modules 
should be incorporated in existing lightening protection equipment. For this, take into 
account the relevant valid regulations (e.g. EN 62305 and VDE 100). 

NOTE

Maintenance and servicing

A photovoltaic system needs practically no 
maintenance, as the solar modules are cleaned 
by the rain at the recommended minimum ang-
le of 15°. To avoid reductions in yield, we do, 
however, recommend carrying out a regular vi-
sual check on the module surfaces. Particularly 
heavy soiling (e.g., leaves) can cause shades 
which reduce performance and should there-
fore be removed. Clean the glass surface with 
water, a water-ethanol- or water-isopropanol 

intermixture and a soft nonabrasive cloth only. 

In exceptional cases, a conventional cleaning 

agent may also be used in the recommended 
dose. Do not use aggressive cleaning agents 
or metal objects, as they can be particularly 
damaging to the hardened glass surface. The 
electric cables should (where accessible) be 
checked regularly for damage, corrosion, and 
firm hold. Pay particular attention to DGUV 
regulation 3 and DIN VDE 0105-100.

Disposal

Dispose of defective or old solar modules pro-
perly; they should never be disposed of with 
domestic waste. The disposal of solar modules 
is regulated in the EU Waste Electrical and 
Electronic Equipment Directive (WEEE). Old 
solar modules can be mostly returned in usual 
commercial quantities to nearby municipal 

collection sites and local civic waste collec

-

tion points at no charge. The WEEE Directive 
is nationally oriented, meaning that each EU 

Member State has its own legal regulations 

and practical handling for the sale and return 

of PV modules. 
Contact us by e-mail at [email protected] 
and specify the number and type of modules 

to be returned. We will then coordinate all 

further details for returning your modules.

SUBJECT TO CHANGE | © 2017 SOLARWATT GMBH | AZ-TM-PMS-0673 | REV 012 | STATUS: 08/2017 | PAGE 27

Summary of Contents for Vision 60M high power

















Reviews: