background image

Fastening on short sides

The maximum pressure load to the solar module 
for the installation conditions is 2,400 N/m². 

 Vertical installation for modules without additional feature “crossrail”

areas approved for fastening

substructure

20

mm

20

mm

Fastening on long sides

The maximum pressure load to the solar module 
for the installation conditions is 2,400 N/m². 

 Vertical installation for modules with and without additional feature “crossrail”

areas approved for fastening

substructure

100 mm

100 mm

Fastening of Module on long and short edge

The lower mounting rail needs to be repositioned 
such as to allow the bottom frame of the module 
to rest on the rail in its full length. Clamps with a 
clamping surface of at least 8x100mm are to be 

utilized. 

The maximum pressure load to the solar module 
for the installation method is 4,200 N/m². 

Vertical installation for increased snow load (with and without additional feature “crossrail”)

substructure

1,

15

0 ± 1

0 m

m

 

245 ± 5 mm

245 ± 5 mm

PAGE 22 | SUBJECT TO CHANGE | © 2017 SOLARWATT GMBH | AZ-TM-PMS-0673 | REV 012 | STATUS: 08/2017

Summary of Contents for Vision 60M high power

















Reviews: